chuds DF33 from OSE

[CHUD]

OK guys
I got this mono from OSE and ITS F/in sweet
I'm droppin my ul/1 motor in it,
with a T120/FROM HK;and a 150/3.16 flexshaft ket with drivedog/&nut OSE also come's with teflon great buy,also props to test on38mm40mm 45mm47mm two bladded from kintec
,aslo brass tubin 1/4x014 from OSE/speedmaster strut from OSE,with carbon fibber 2'' turn fins OSE,,TACTIC 2.4g receiver,a water cooled motormount from fightercat, and here some pic's

[HYDROJERRY]

Get-R-Done,,,bro.. ps i dig the flower print in the background..

[CHUD]

Two start the hull off ,I just looked at it
I was thinkin should I put carbonfibber in the bottum you guy's let me no.
than I went ahead and started with the speedmaster strut, I found it easy if you take the thing apart and drill the hole,s Here's some things I am going to use,, pick's

[CHUD]

Placing the bracket was easy just make sure your 3/16 two a 1/4 off the bottum of the boat,and I also found it's easy if you drill one hole and put a screw in the bracket snug it up easlly than make sure your bracket is nice and even ,than drill another hole and another untill all 4 hole's are complete,it will look like this

[CHUD]

Get-R-Done,,,bro.. ps i dig the flower print in the background..

Thanks bro Ya I wish I had some skulls & crossbones

[CHUD]

Know after putting the speedmaster back together, I made sure it was straight ,mount it two the boat and I used a drill bit to mark ware the brass tubin is going ,Than I removed the strut, and I started with a small drill bit ,than I used anther bit alittle bigger ,three bit,s and I was done,The brass fit's nicely and not to tight,I 'm only going to leave the brass out about1/2 of a inch,just to see if everything line up I put my teflon in than my 1.50 /316 flex with drive AND everyth ing is on trake, instead of epoxying in the brass I'M going to take it out untill later,

[CHUD]

Well today I drilled and put the trim tabs' on ,pulled in on each side and marked 2''inches,Know on to the turn fin's can anybody tell me the way to put the turn fins on ,is it straight up and down or turned out just a little,I have seen it two way's here on OSE,

[CHUD]

Well I'm done,me and hydro put some c/f in for rail's and it worked out fine , I ,m pretty sure the ul,1 motor will move the boat just fine,maybe around 35 or 40 pending on prop, I ,m testing tomorrow and than workin on the paintjob,Thanks bro for the help!

[HYDROJERRY]

Ill see you there with the blowup raft,,hehehe..

[bruiser77]

Nice build! Gonna post any video?

[CHUD]

Thank's bruiser and welcome to OSE, I hope hydro jerry bring's it out,in the morning,how about it bro

[HYDROJERRY]

yep!!!!

[CHUD]

Well I made my first run the weekand ,with props 38mm 40mm 45mm and the best one was my three bladed prop 37mm BUT I just diden't have enough power so I think I should have got a 540 motor for the boat I'm looking at the turnigy 3674 B 2200kv//or turnigy 4074 B 2000kv ,ANY INFO WILL HELP!!

[fastblack]

you should not use 2200kv or 2000kv too much kv in df33hull. maybe 2000kv will work on 4 cell but it wont be very fast. 4 cell is not enough in this hull. i would go for a leopard 4074 1400kv or 4082 1500kv, then you can run 42-45mm props at 6 cell lipo and this will move the boat in speeds around 80-90kmph, a leopard 4074 1400kv with x642 prop draws about 90-100amps in this hull on 6cell. this is a very nice stable setup. speed 80kmh. i have run this hull with 40mm prop but it doesnt like 40mm prop seems like 42mm prop is minimum for this hull and 42mm works great, with 40mm prop it looses (traction) (slips in the water) (spins out)all the time.... (im not good at english)

of course you could get this hull moving on 4cell 45-90c if your amp draw was 140-150amps but then you get very low(bad) runtime... also you would need a 180amp speedcontrol...

[CHUD]

Fastblack can I use my t120 with the leopard 4074 1400kv and 6 cell' and will I get good run time 's