BBY War Zone Jr

[RandyatBBY]

I woke up this morning and decided that you need a little help. I watched the video and you have no rpm to hold the bow anywhere, the front of the boat will fallow any wave it hits and go up and down as it flows over the water. Either get a 3S battery or a hotter motor. You have a 3600 Kv motor you need to zing it a little. How big is the prop? Your rudder is way too long you only need 1/2 of and inch below the lowest point of the prop, it is like a big anchor slowing you down. I am going to setup my WZ Jr. and run it this weekend and take a video. That way I can show you guys what it can do. I am trying to be constructive hope you do not take me as rude, I am trying to help.

I had another idea too, I might lower the price on the OM21 so you guys will buy it and have a better platform to run form too. If we can to get this little hull flying I will give you a new OM21.

[BILL OXIDEAN]

That boat needs trim tabs for starters. I think there's way too much hardware on there too that strut is huge as well as that rudder bracket.

That package would be on a European 4s mono!

[RandyatBBY]

That boat needs trim tabs for starters. I think there's way too much hardware on there too that strut is huge as well as that rudder bracket.

That package would be on a European 4s mono!

You have a point there, I was thinking about it but did not get to it. I thought it was the little boat making it look big it is a 1/8 flex and stub?

I bet a N1/ Novack motor would be the ticket. Like a 10.5 or a CC Mamba 5600?

[j.m.]

You have a point there, I was thinking about it but did not get to it. I bet a N1 Novack motor would be the ticket. Like a 10.5 or a CC Mamba 5600?

A 10.5 turn Novak motor is 4200 Kv, and CC doesn't make a 5600Kv motor... They do however make a 4600Kv motor.

[RandyatBBY]

A 10.5 turn Novak motor is 4200 Kv, and CC doesn't make a 5600Kv motor... They do however make a 4600Kv motor.

I am not in my shop to look at the motor to be correct is it a 5800?

[j.m.]

100 low, 100 high...

It's a 5700. SWEET motors. Probably one of the most popular ever in the brushless car scene, especially before Novak started getting less expensive.

Here's a good buy:

http://www.shopatron.com/products/productdetail/RMF+SS+Pro+Brushless+Motors/part_number=S341X/135.0.1.1.7521.26355.0.0.0?

(8.5t = 5000Kv)

If your using it with a sensorless esc, i have pics on how to completely remove the sensor system...

Jon

[RandyatBBY]

100 low, 100 high...

It's a 5700. SWEET motors. Probably one of the most popular ever in the brushless car scene, especially before Novak started getting less expensive.

Here's a good buy:

http://www.shopatron.com/products/productdetail/RMF+SS+Pro+Brushless+Motors/part_number=S341X/135.0.1.1.7521.26355.0.0.0?

(8.5t = 5000Kv)

If your using it with a sensorless esc, i have pics on how to completely remove the sensor system...

Jon

I woke up a little early today thinking about everything so at 61years my brain is a little fuzzy. so many motors I just do not try to keep track.

I was thinking that a little better help would be to take a motor that is closer to what he has and run it. I would have to make it work to show waht to do. How about the little Micro out runner? It had 3000 Kv and close in power on 2S.

Got to work on a mold, back in a while......

[RandyatBBY]

Not to hijack your thread , just trying to help. this is my hardware and I think the rudder is too and I will be putting a thiner blade rudder on.


Motor I am planning on using


The boat I have not ran my self since 1999

[wakeboardfusion]

I woke up this morning and decided that you need a little help. I watched the video and you have no rpm to hold the bow anywhere, the front of the boat will fallow any wave it hits and go up and down as it flows over the water. Either get a 3S battery or a hotter motor. You have a 3600 Kv motor you need to zing it a little. How big is the prop? Your rudder is way too long you only need 1/2 of and inch below the lowest point of the prop, it is like a big anchor slowing you down. I am going to setup my WZ Jr. and run it this weekend and take a video. That way I can show you guys what it can do. I am trying to be constructive hope you do not take me as rude, I am trying to help.

I had another idea too, I might lower the price on the OM21 so you guys will buy it and have a better platform to run form too. If we can to get this little hull flying I will give you a new OM21.

I will take you up on this Randy. I will start to tweek it and get it running good!

[j.m.]

If we can to get this little hull flying I will give you a new OM21.

I don't need any hulls, but I'll take hardware handouts!!

I may eventually do a 2s mono to run with my car lipos.

About the video, MORE SPEED!!! Get that prop spinnin and the hull out of the water. More weight is NOT better. Keep it light and powerful. CG adjustment is key to good performance.

Jon

[RandyatBBY]

My typen and missing a letter seams to be missunderstood. I was saying that If we can NOT get this little hull flying I will give you a new OM21.

[j.m.]

My typen and missing a letter seams to be missunderstood. I was saying that If we can NOT get this little hull flying I will give you a new OM21.

Im still open to hardware offers.....

[boater76]

I have the same hull was going to run the same motor with a 45amp esc. And push the limit of the motor with a pair of 2s packs. Still waiting on the rest of my parts to arrive plus my stinger was just sent to Jeff Wohlt to have a custom shaft made.

[boater76]

I do have an extra outrunner though too. But I have to see what will take volt wise.

[wakeboardfusion]

My typen and missing a letter seams to be missunderstood. I was saying that If we can NOT get this little hull flying I will give you a new OM21.

Oh haha ok, I was like woo hoo free hull.