My scratch built Pontoon

[in-d-boat]

cont.

Found a home for the servo and put the sheeting on the deck. I might add that I used the Bondex plastic cement rather than super glue. The Bondex melts the plastic together and forms, more or less, a solid joint. Where super glue will stick the pieces together ok, but doesn't bond them toether. Pieces will just snap apart. I never tried using the made for plastic super glue. Maybe that would work as well. The droplets are water from test floatin' it.DSC00514.jpgDSC00515.jpgDSC00516.jpgDSC00517.jpgDSC00518.jpg

[srislash]

I kept skipping by this thread for some reason,but now I'm glad I stopped.That is really cool work there and it turned out fantabulous.I spent alot of time on these in the Okanagan here in B.C. This looks so cool,thanks for sharing.

Shawn

[in-d-boat]

cont.

Then it was on to roughing in the sides. I made these with 1/8" square styrene and sheeted them with .030" Used a heat gun to soften the plastic and formed the radius around a 1/2" dowel. Too much heat and it screws up the plastic. Not enough, and it won't hold the shape. Alot of trial and error to get it right. You can "feel" when the plastic is the right temp. Hard to explain.DSC00521.jpgDSC00522.jpgDSC00523.jpgDSC00524.jpgDSC00525.jpg

[in-d-boat]

Thanks a ton, Shawn. Happy that you like it!

[in-d-boat]

cont.

Next came the helm and some "cushy" boat furniture. The cushions for the benches were made from using 5/16 x 1/4 1/2 bulb weather stripping. Works good and has an adhesive back. A lot of "that looks about right" hereDSC00538.jpgDSC00540.jpgDSC00542.jpgDSC00544.jpg

[Make-a-Wake]

Very good work!!!

[in-d-boat]

cont.

I made a couple of "life jacket" storage boxes for the rear deck. One has the receiver in it, the other one has the ESC. It's a box over another box type of thing. All the wiring is routed above the center pontoon and never gets wet.DSC00548.jpgDSC00549.jpgDSC00550.jpgDSC00551.jpg And thanks again Make-a-Wake.

[in-d-boat]

cont.

The battery compartment needed to be towards the bow and below deck. Also shows the rectangle channel for the battery wires to the center pontoon, through that to the ESC. A long lead doesn't seem to be a problem. It has room for 2 batteries but 1 runs forever. Not a speedy boat. Part throttle=looooong run times. DSC00552.jpg

[in-d-boat]

cont.

Then I made a Bimini top for it. Used 1/8" round for the frame work. A couple of 1/8" square for the rear stationary supports. And 2 .010 thick "straps" for the front.DSC00558.jpgDSC00559.jpg

[in-d-boat]

cont.

The whole boat was painted aluminum, 4 coats. I used Mono Kote trim sheets for the white and the designs. Sprayed Windex on the cut out sheet first, then "floated" them into place.DSC00560.jpgDSC00565.jpgDSC00568.jpgDSC00584.jpg The floor (carpet) is 2MM foam stuff I picked up at a Hobby Lobby craft store. And what pontoon boat would be complete without a grill? That's made out of a fishin' bobber and some leftovers. The tables are out of pizza boxes, I guess so the pizza doesn't stick to the lid. LOL.
That pretty much covers it. Thanks for all the positive comments, guys! DSC00617.jpg
In-D-boat

[srislash]

Boy,that is great detail.And 1/12 scale? It would look good on the beach next to my scale truck




Sorry bud I couldn't resist the pic and this is probably as scale as I possess for now.

P.S.: I love the grill and table.

[in-d-boat]

Thank you! Cool truck! (Hummer?) Is that a winch on the front? Functional? Looks like I should get busy and make a trailer for the pontoon.

[srislash]

Nope,it is just a toolbox.I needed it to fill in the huge hole between the lights and the bumper.I don't believe in winches for the 1:1 rigs either.There comes a point when hiking is quicker.Hehe

[hazegry]

I hope you dont mind but I am so going to replicate this and build one for myself.

[in-d-boat]

Heck, no. I don't mind in the least. I would consider it a compliment. I just wish I had some plans to pass along, but I don't. Sorry. Do you have an EP-1? Any outboard heavier would probably make her a little tail heavy. (or increase the lenght of the center pontoon and lower the center some for some extra flotation ) I have some 2 1/4" tubes that if I make another one I might see about the Stilleto outboard for that. But that would be down the road some. Thank you!