2015 West Florida Model boat club, Sarasota, FL

[RCKong]

Looks like the weather is going to be nice over the weekend for a change...

[flraptor07]

YUP! We're running SUNDAY!!

[RCKong]

Sounds good !
I plan on being there

[RayR]

Count me in.

[ron1950]

when is the after Christmas run date? ill be down with one boat maybe

[HRC]

Ill be there

[flraptor07]

Anybody else gonna be there? Let us know...

[richard]

I will be there

[bill34207]

I'm going to try to drop by around 10:00 or so. Not planning on running but will have my camera.
Got my 1st flight on this one today https://youtu.be/ohYkwSi3iHs

[HRC]

HA..you got it put together Bill. Stuck the landing :)

[TRUCKPULL]

VERY NICE BILL

Larry

[TRUCKPULL]

Dave

Anything on the rudder extension yet??

Larry

[HRC]

Dave

Anything on the rudder extension yet??

Larry

Hi Larry,
I am about half way through the cnc programming of it. I have the 8 mm width and the .119 cut out with the extended section. How tall do you think it should be?

[ron1950]

bill its so quite you don't even know its a real jet ..love it

[bill34207]

Thanks guys. I guess I forgot to mention that it was not me flying. I have to take credit for the shaky camera work instead. For some reason, any time I shoot video of someone else flying one of my planes, it always coming out shaky.
I did fly it a little while after that but it didn't get caught on camera.

[TRUCKPULL]

Hi Larry,
I am about half way through the cnc programming of it. I have the 8 mm width and the .119 cut out with the extended section. How tall do you think it should be?

Dave
It measures out at 27mm = 1.063" tall. If 1" better for material usage -OK -- Just keep the up and down spacing between the holes at 17mm

The bottom measurement on the upper diagram it the actual standoff amount .750 (3/4")
After doing some more calculations, I think this measurement should be 1"

Is this do-able ????????

Larry

[bill34207]

Video from today is uploading. I'll let y'all put them in the thread and supply the commentary.

[HRC]

Video from today is uploading. I'll let y'all put them in the thread and supply the commentary.

Thanks Bill, I found the vids on your you tube.

[HRC]

Dave
It measures out at 27mm = 1.063" tall. If 1" better for material usage -OK -- Just keep the up and down spacing between the holes at 17mm

The bottom measurement on the upper diagram it the actual standoff amount .750 (3/4")
After doing some more calculations, I think this measurement should be 1"

Is this do-able ????????

Larry

Larry,
I sent you a PM

[rdcracer]

I was busy earlier in the week and didnt get a chance to check the site and when I woke up sunday it was blowing about 15 mph.out of the east.
I figured it would be a mess at the lake. I couldnt even fly my drone it was so bad. Sorry I missed it.

[RCKong]

Merry Christmas & Happy New Year !

[RayR]

Merry Christmas to All!

[TRUCKPULL]

Marry Christmas & Happy New Year

Will see you all at the end of Jan.

Larry

[bill34207]

Merry Christmas to All

[HRC]

Merry Christmas. I guess we will not be running Sunday?

[RayR]

Merry Christmas. I guess we will not be running Sunday?

Calling for SE wind at 21. nope.

[bill34207]

Calling for SE wind at 21. nope.

I see you noticed that too.
It's a plot. I'm on vacation until Jan 4th so it will probably be crappy windy weather until I go back to work.

[rdcracer]

Merry Christmas everyone

[bill34207]

Any thoughts on putting together a New Years day run at Encore? No telling what the weather will bring but I recall having one there a few years ago and it was pretty good.
Also, you guys need to check out the clubs Facebook page. https://www.facebook.com/groups/529601763719875/

[RayR]

Any thoughts on putting together a New Years day run at Encore? No telling what the weather will bring but I recall having one there a few years ago and it was pretty good.

I won't be available on New Years Day, Tampa airport run to pick up a friend.

As well, I started moving the course yesterday. I only got the North end done before running out of battery power.