FighterCat and Flier ESC's 3-20S 10A, 3-16S 300A and 3-8S 400A ESC's

[RaceMechaniX]

Hello All,

I have been hanging onto these long enough and don't plan on running so they are up for sale.

First ESC is Fightercat branded Flier ESC rated at 3-20S and 80A maximum. This was a special extra HV version. It's been bench tested, but never run in a boat. Asking $150 Shipped.

Second ESC is a Fightercat branded Flier ESC rated at 3-16S and 300A maximum. This was the standard HV version. It's been bench tested, but never run in a boat. Asking $250 shipped. ***Sold to meangeneracing***

Third ESC is a Flier double board 3-8S 400A ESC. This was a prototype them made for me. It comes with the USB programmer and the handheld programmer. It's set-up for a rotary pot switch instead of the normal receiver connection as I was using it for bench testing motors. The USB programmer and online software will allow it to be converted back to a normal receiver input. I will have to email the buyer a copy of the software. Asking $250 shipped. ***Sold to Blake T***

I can change any of the settings in any of the controllers prior to shipping if you do not have the programming box. These are getting hard to find.

I am open to trades for Lehner motors or other ESC's like YGE, Schulzes, Kontroniks of equal value.

-TylerFC 3-20S 80A ESC Pic 1.jpgFC 3-16S 300A ESC Pic 2.jpgFC 3-16S 300A ESC Pic 1.jpgFC 3-20S 80A ESC Pic 2.jpgFlier 3-8S 400A ESC Pic 1.jpg

[RaceMechaniX]

Additional picture of the double board 400A controller.Flier 3-8S 400A ESC Pic 2.jpg

[meangenesracing]

Tyler, I will take the 300A if it would work for my setup we talked about in the Backlash with a TP 5680

[RaceMechaniX]

Hi Eugene,

Yes this ESC will work well with the 5680. I tested an 8S 300A FC controller with a 5670 in my Q hydro. Ran good with no issues.
I can program in the timing numbers for you before I ship. Did you decide on the wind yet?

-Tyler

[meangenesracing]

Sorry Tyler I should have specified 10s I decided on. Either the 5y. 650 kv or the 4y 800 kv. Steven has both in stock. Which one you think? thanks

[BlakeT]

Hi Tyler, I’m interested in the 3-8s 400 amp esc. Any chance you would be able to program it back to normal before shipping it?

[RaceMechaniX]

Hi Blake,
Yes I can program it back and check it before shipping to you.
-Tyler

[BlakeT]

Thanks Tyler, I will take it. I’m just not too savvy with technology, It still comes with program box?

[RaceMechaniX]

Sorry Tyler I should have specified 10s I decided on. Either the 5y. 650 kv or the 4y 800 kv. Steven has both in stock. Which one you think? thanks

Eugene it will depend on what size props you want to run. 650 would likely be the best as you can run gas size props will hook up better in rough water. With 800kv you will be more limited in prop selection and in a purgatory range between 3/16" and 1/4" bores. Go with 650kv.

[RaceMechaniX]

Thanks Tyler, I will take it. I’m just not too savvy with technology, It still comes with program box?

Blake, yes the 400A double will come with the USB programmer and the program box.

[meangenesracing]

Eugene it will depend on what size props you want to run. 650 would likely be the best as you can run gas size props will hook up better in rough water. With 800kv you will be more limited in prop selection and in a purgatory range between 3/16" and 1/4" bores. Go with 650kv.

OK sounds good the 650 kv it is with the 300 amp esc. I think I still have your paypal addy. I'll get it sent shortly, thanks again

[meangenesracing]

Paypal sent

[BlakeT]

Sounds good, when you have time can you send over your paypal address in a PM, thanks!

[RaceMechaniX]

Hello Eugene, Money received. I will get this in the mail tomorrow.
Blake, PM imbound for the PP address.

Thx,
Tyler

[meangenesracing]

Hello Eugene, Money received. I will get this in the mail tomorrow.
Blake, PM imbound for the PP address.

Thx,
Tyler

Ok thanks Tyler, please program for my setup as I don't have a program box. No hurry on shipping

[RaceMechaniX]

Ok thanks Tyler, please program for my setup as I don't have a program box. No hurry on shipping

Got it. If you don't mind I will ship it early next week. I am off to a time trial today and would need to pull the programming box which is buried in a tool box.
-Tyler

[meangenesracing]

Got it. If you don't mind I will ship it early next week. I am off to a time trial today and would need to pull the programming box which is buried in a tool box.
-Tyler

Sure thing Tyler, no hurry on shipping

[BlakeT]

Money has been sent, thanks again!

[RaceMechaniX]

Received. Thx Blake.

[RaceMechaniX]

Hi Eugene, ESC will ship tomorrow. I set the timing to 10Deg, low start power, 8kHz drive frequency and no reverse. Tested again on the bench and all works OK. I will PM you the tracking number.

Blake, I could not reprogram the ESC to work with a normal radio input. It will only work with the variable pot switch it came with. I assume this is of no use to you so I will refund your money. I do have a Fightercat 2-8S 300A controller I can replace it with for a reduced price. Let me know.

-Tyler

FC.jpg

[Bp9145]

Hi Eugene, ESC will ship tomorrow. I set the timing to 10Deg, low start power, 8kHz drive frequency and no reverse. Tested again on the bench and all works OK. I will PM you the tracking number.

Blake, I could not reprogram the ESC to work with a normal radio input. It will only work with the variable pot switch it came with. I assume this is of no use to you so I will refund your money. I do have a Fightercat 2-8S 300A controller I can replace it with for a reduced price. Let me know.

-Tyler

FC.jpg

Tyler, if Blake will not take the Fightercat 2-8S 300A controller, I'm interested depending on price.

[RaceMechaniX]

Yep, I told Blake he gets first crack at it. If he passes I will make it available to you.

[Jesse J]

Interested in #1, but maybe when you get down to $100 shipped.
And please put me in line after mr. Pino for the 300amp 2-8s controller.

[RaceMechaniX]

Blake is going to take the 8S 300A controller.

Jesse, I can do $110 shipped for the 80A controller.

[BlakeT]

Payment sent, thanks again Tyler

[RaceMechaniX]

Hello Blake,
Payment received. I will pack up tonight and ship out tomorrow.
-Tyler

[RaceMechaniX]

Blake, ESC went out yesterday. Both you and Eugene should have received tracking through PP. Let me know if you did not.

Thanks,
-Tyler

[Jesse J]

Blake is going to take the 8S 300A controller.

Jesse, I can do $110 shipped for the 80A controller.

I’ll wait for $100 days. No rush.

[meangenesracing]

Blake, ESC went out yesterday. Both you and Eugene should have received tracking through PP. Let me know if you did not.

Thanks,
-Tyler

Tyler, my esc was waiting for me when I got home last night, thank you sir

[BlakeT]

Mine says it will be here Monday, thanks!