Here you can see the two epoxy formed ride pad bays.
And a close up shot...
Sent from my SM-G950U1 using Tapatalk
Here you can see the two epoxy formed ride pad bays.
And a close up shot...
Sent from my SM-G950U1 using Tapatalk
Don't forget flotation, just in case.
very nice.
Has anyone tried spray foam for flotation?
They use it in 1/1 boats. My local hardware store has low expansion, weatherproof spray foam I'm thinking about trying.
Sent from my SM-G950U1 using Tapatalk
Here's a link to 1/4" teflon for epoxy forming carbon fiber...
https://rover.ebay.com/rover/0/0/0?m...2F143012082779
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 12-01-2018 at 06:22 AM.
Testing the expansion rate of the spray foam...
When I squeeze the epoxy cup, I feel no pressure on the sides. The pressure is escaping upwards.
Sent from my SM-G950U1 using Tapatalk
A mod to the PVC pipe clamps. Zip tying polyurethane strips to them for grip so they don't slide around, and so they don't mark the birch plywood sheeting...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 12-01-2018 at 09:38 PM.
Yes, I epoxied the sponson tubes.
Even tho I know the expansion rate, I still overfilled the sponsons. Trust that the foam will fill them...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 12-01-2018 at 09:39 PM.
They must sit overnight. It takes that long to completely cure. I checked this out in the epoxy cup. Do not bump them, the foam will collapse and lose air bubbles.
This is the final expansion the next day...
Sent from my SM-G950U1 using Tapatalk
The foam trims flush easily with a serrated knife...
Sent from my SM-G950U1 using Tapatalk
Setting up for epoxying the top deck...
Sent from my SM-G950U1 using Tapatalk
One sponson done and curing!
Sent from my SM-G950U1 using Tapatalk
Sammy,
Is that foam fairly light? Some of that stuff that I've seen is pretty dense and heavy.
Bob
Keeping the tape on the right sponson, at least overnight. Pulled the clamps, the left sponson sheeting is on.
I must say, there's a lot of techniques for sections of a wood boat build to figure out. Mike says the sponson top sheeting is the hardest part of the build...
It's amazing how they are pumping out all those nice quality RTR's.
They must factor the time and cost to build into the construction/assembly part of the design. Yet they have a nice finished look to them along with great performance. Smh...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 12-02-2018 at 11:01 AM.
Pulled the tape, trimmed the top sheeting. I succeeded in getting all the epoxy joints tight...
Sent from my SM-G950U1 using Tapatalk
Very nice,
I have power tool's, it will fit
I asked about spray foam, no one responded.
Here's my very scientific comparison between four types of foam...
Sent from my SM-G950U1 using Tapatalk
White foam, very soft and light...
Sent from my SM-G950U1 using Tapatalk
Packing peanuts, basically just air...
Sent from my SM-G950U1 using Tapatalk
Spray foam, the heaviest in my study. Structurally the strongest, not really that much heavier. Not enough to be a concern...
Sent from my SM-G950U1 using Tapatalk
Pipe insulation. Firmer and more dense than the white foam. Right in the middle for weight...
Sent from my SM-G950U1 using Tapatalk
Can anyone tell me if the inside sponson to sponson measurement of 14-7/8" given in the manual applies to the RSX380?
The manual is for all three riggers, are they all the same?
Scaling these drawings, they don't look to be the same...
Sent from my SM-G950U1 using Tapatalk
I bought a Map torch and some good silver solder. The real stuff, 45% silver brazing alloy...
Sent from my SM-G950U1 using Tapatalk
And some 1/16" galvanized cable.
The copper tabs are cut out from split open and flattened copper tubing...
Sent from my SM-G950U1 using Tapatalk
I drilled the copper tabs and formed them around the cable. The cable is folded over about 3/8" from the end and silver soldered in...
Sent from my SM-G950U1 using Tapatalk
I'll run the cable on the back side of the sponson rods and put shrink tubing over the cable and rods at final assembly. The copper tabs will be bolted on with the screws retaining the sponsons.
I'm putting a cable on the front and back rods. That's 1/8" OD brass tubing going thru the tub.
I don't think I'd put a rigger in the water without safety cables to keep the sponsons attached to the tub...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 12-02-2018 at 11:16 PM.
Sammy,
What are the cables for, Just safety to keep from losing the tub if you break the booms?
Bob
Bookmarks