Then I removed my servo tray.
It weighs 1.05 ounces and the CG moved about half the thickness of the spruce strip. An eighth of an inch...
Interesting? It sure is too me...
Sent from my SM-G950U1 using Tapatalk
Then I removed my servo tray.
It weighs 1.05 ounces and the CG moved about half the thickness of the spruce strip. An eighth of an inch...
Interesting? It sure is too me...
Sent from my SM-G950U1 using Tapatalk
The question is, what does this mean, real world?
Other words, what difference in handling would moving the CG an 1/8" make? Would you even notice the difference? I don't know the answer to that...
I can figure this much tho. From the CG point to the center of the back bay measures 17", and it's 15" to the tips of the sponsons.
That a 1.13/1 ratio.
For an ounce heavy in the back you would need 1.13 ounces in the front.
So weight in the back is something to avoid.
It's a bigger deal with airplanes, more like a 3/1 ratio.
This should balance nicely...
Sent from my SM-G950U1 using Tapatalk
I doubt very much you will notice any difference by moving the c.o.g. back or forward even by 1 inch each way.
The position of your turn fin in relation to the CG is more important.
NZMPBA 2013, 2016 Open Electric Champion. NZMPBA 2016 P Offshore Champion.
2016 SUHA Q Sport Hydro Hi Points Champion.
BOPMPBC Open Mono, Open Electric Champion.
I share this because I think it worked out quite well. Maybe someone else building a rigger can use this.
You have to buy two, to get eight pads(or cut more pads from the scrap). They are $10.99 each, I got the carbon fiber ones... https://www.offshoreelectrics.com/pr...prod=ose-80525
The pictures tell the story...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-16-2018 at 10:13 AM.
I got my battery straps figured out...
https://youtu.be/pb5P7KMyRgg
Sent from my SM-G950U1 using Tapatalk
well done , your doing a great build .
Mounting the Spearfish 200A ESC is another challenge with this build. It's huge! After studying this for quite awhile, I figured this was my only solution.
Although I removed the top cross section of the middle former, the braces under the ESC mount more than replaces it for strength.
The end result worked out to my satisfaction...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-16-2018 at 07:52 AM.
Still have to add velcro under the ESC.
In the second picture, the top of the former is now removed...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-16-2018 at 07:51 AM.
Here's an overall look with batteries in place.
Everything fits under the cowling...
Sent from my SM-G950U1 using Tapatalk
I love the way this kit goes together...
Sheeting the rear sponson shoes with 1/32" birch plywood. I made many more small epoxy mixes, carefully spread with a screwdriver on all the formers and basswood strips.
Since tacking the main tub and sponsons together with CA, I've used epoxy throughout this build.
More time consuming but worth the strength...
Sent from my SM-G950U1 using Tapatalk
Bottom ride pads forming nicely in one continuous piece up the leading angle...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-20-2018 at 06:34 AM.
The top and bottom sheeting overlaps the side sheeting.
Sent from my SM-G950U1 using Tapatalk
Stripped the hardware and electronics, sanding the tub before sealing with epoxy...
Sent from my SM-G950U1 using Tapatalk
Shaping the nose block and 1/4 round. Sanding edges and bedding the rear sponson shoes...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-21-2018 at 08:02 AM.
Sammy,
You can build a boat for me anytime. Beautiful job, and great job with the build log.
Bob
The inside of the tub is epoxied. The "bend the acid brush" tip was in use for all the hard to reach corners...
Sent from my SM-G950U1 using Tapatalk
Here's why I save scrap. Perfect use for titanium, it won't rust and I'll never strip these threads.
On the down side, I wrecked a brand new Dewalt hacksaw blade.
The chamfers and radius are clearance for the epoxy joints inside the sponson. I nested the titanium block in hardwood...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-24-2018 at 07:50 AM.
The hardwood gives the epoxy better bite than the titanium alone and spreads the load forces...
Sent from my SM-G950U1 using Tapatalk
coming along very nicely.
I'm also epoxy forming the carbon fiber in the sponsons. Just the two ride pad bays.
I feel that this is similar to vacuum forming. Not exactly the same, I know. But it forces the epoxy thru the CF and gets a better bond to the wood.
I'm doing it slightly different than from how I did the tub. I'm not trimming the CF inside the sponsons. I can get away with doing it this way working with smaller pieces. Plus it will be covered up. This is only for strength. The ride pads probably take more pounding than anywhere else on a rigger.
I'll roll some pictures...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-28-2018 at 11:03 AM.
I placed the CF in there and pressed it down with the teflon to tuck in the corners.
Then I removed the teflon, poured in some slightly thinned epoxy, just enough so it squeezed out around the top when I pressed in the teflon again.
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-27-2018 at 06:08 AM.
After weighting it down(on the screws) and curing, I removed the teflon by pulling on the screws...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-27-2018 at 06:12 AM.
excellent work, keep it going.
It's a little hard to take pictures of, but here's some shots of the final result...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-27-2018 at 09:58 AM.
I read in another thread about guys using Klass Kote epoxy paint. I found it on Ebay.
Here's the link to Part A, the colored part... https://rover.ebay.com/rover/0/0/0?m...2F152029025775
This seller also has the Part B catalyst and the reducer for thinning.
I placed my order by adding to basket, he combines shipping. Great seller, I contacted him, fast response...
Prior to this, the only other two part epoxy paint I could find was Coloredepoxies on Amazon for $78.16 per color. This is a 2/1 mix, you have to buy 3 quarts minimum.
Here's my total for white, orange, catalyst and the reducer...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-27-2018 at 09:52 AM.
I have a daytime job too, and I've been pounding the OT.
This part of the build is finished tho...
Sent from my SM-G950U1 using Tapatalk
Last edited by sammyha; 11-28-2018 at 11:05 AM.
Bookmarks