Hello all.
I have an Aqua Craft 36/56 2030KV motor NIB, but nothing to put it in.
Any suggestions?
-Andrew
Hello all.
I have an Aqua Craft 36/56 2030KV motor NIB, but nothing to put it in.
Any suggestions?
-Andrew
What could possibly go wrong?
Put it in a boat!
http://www.vac-u-boat.com/Vac-U-Pickle.htm
try something like a Revolt mono and run it on 4s .
Ok, thanks guys.
-Andrew
What could possibly go wrong?
For what it's worth I have one in my shockwave 26'' and with a few modes and on 3s it tools around 35 for about 6min for fun.
SW26 V3 Green 35mph , Swifter Hydro 26. Delta Force 35. cars ,3 Rustlers 45-76 Mph.
Well with that motor and 4-6S and you'll be having fun!
SW26 V3 Green 35mph , Swifter Hydro 26. Delta Force 35. cars ,3 Rustlers 45-76 Mph.
For the 36" ShockWave this motor is going to work pretty hard.
Too many boats, not enough time...
here's what I did with my AquaCraft UL-1 motor
SAM_3758.jpg
PROBOAT BlackJack 24", ShockWave 26"
MRP U-31, 3 tunnels VS1, MRP Bud Light, Dumas HS Sprint
right here at OSE in the outboard section. $5 bucks if I remember correctly.
PROBOAT BlackJack 24", ShockWave 26"
MRP U-31, 3 tunnels VS1, MRP Bud Light, Dumas HS Sprint
Thanks, l have not been on this forum for a long time, will look into it.
Sent from my XT1650 using Tapatalk
Too many boats, not enough time...
I love your Avatar tunnels.
Too many boats, not enough time...
You plan to run parallel? If you want to run 6s there's only 3300 mAh. It's not enough capacity IMO. Also the ESC will heat up because the batteries are not capable of giving what the motor is demanding.
Best is to get 4S in the 5000mAh range and if l was setting up this 36'" boat. I will run two of these batteries with parallel wiring so l have 10,000 mAh.
Start with a not too aggressive prop and observe the temperature on the ESC.
Just my opinion...
Sent from my XT1650 using Tapatalk
Too many boats, not enough time...
Try and keep that motor on 4S in a 30 ish inch boat. Its not suitable for the 36" shockwave.
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
Pro boat has a 26" green shockwave which will be great on this one. . .plenty of power and you can use your 120A if desired, of course higher will be better. But, in this case it will be fine and you can get the shockwave hull relatively cheap and put some nice hardware.
Ok guys.
Thanks for all the input. It is a bit small for the SW36. Maybe it will be more suitable in a small or med size rigger. I always wanted one any way.
-Andrew
What could possibly go wrong?
grab yourself a nice JAE/ 21 FE for that 2030 kv motor on 4s or 6s for SAW.
I ran that motor in a Revolt on 4s and it ripped. Also lowered the battery tray.
white geico w/2200kv 3674 leopard 53.5mph 4s2p, geico w/ 1800kv outrunner 52mph on 4s2p, genesis w/2200kv castle 53.8 on 4s2p, impulse 31 w/2200kv castle, stock p1 and ul-1
Hi,
I would imagine how well it did in that hull. AquaCraft was doing well, but then a whole series of events unfolded and Grim Racer left. Now TowerHobbies is under Horizon Hobby and I see the boat is back in stock. I wish AquaCraft well....
I never thought TowerHobbies would go under, sad. Especially it was an employee owned operation.
Enough rant.
Cheers!
Happy 4th of July!!!
Too many boats, not enough time...
Wasn't Horizon started by a group of people that left Tower?
-Andrew
What could possibly go wrong?
Bookmarks