ABC high pitch props

[MG1234]

A 2014,I'll look that up on my chart ,you have to sharpen and ballance yes?

[zooma]

Travis, are these ABC cleaver props detongued to approximately the same as Octura M props?

[MG1234]

And do they need to be finished? Or are they ready to go? They look like they need finishing,

[dmitry100]

of course they need sharpening and balancing ... talk to dasboata about that.

[MG1234]

So that's a 2" prop ,do any ABC come finished? What boat are you putting that monster on ?

[kfxguy]

All abc props need finishing. The new ones are very closely balanced out the bad tho. I ran a couple raw for the heck of it and results were poor. They need sharpening and balancing.


The big prop is slated for my shocker build. Maybe even try it on my kbb34 on lower voltage.

[Turbo Dan-O]

...

[dmitry100]

What are you gonna run that 2014 abc on, kfxguy?

[Jamey]

Travis, are these ABC cleaver props detongued to approximately the same as Octura M props?

Sorry not Travis but I can tell you they are detongued MORE than Octura M. That is why they have less bite at slower speeds but are very efficient at high speeds.

[Jamey]

All abc props need finishing. The new ones are very closely balanced out the bad tho. I ran a couple raw for the heck of it and results were poor. They need sharpening and balancing.


The big prop is slated for my shocker build. Maybe even try it on my kbb34 on lower voltage.

I was thinking of trying the 2014 on my pursuit, especially when running 5S. Let us know how it does if you try on your kbb34. Thinking it will be very close to a 1915 speed wise.

[zooma]

Sorry not Travis but I can tell you they are detongued MORE than Octura M. That is why they have less bite at slower speeds but are very efficient at high speeds.

Sounds good.

[MG1234]

Wow I'm the only guy in 100 miles with a RC boat,that's why I need so much advice ,:)

[rayzerdesigns]

All abc props need finishing. The new ones are very closely balanced out the bad tho. I ran a couple raw for the heck of it and results were poor. They need sharpening and balancing.


The big prop is slated for my shocker build. Maybe even try it on my kbb34 on lower voltage.

the new ones I got were way out of balance

[kfxguy]

the new ones I got were way out of balance

Make sure the hole drilled through it is centered. There was a bad batch here recently because tooling got messed up. It's straightened out now.

[Turbo Dan-O]

Just got in this 1715-17. It's waaaay heavy on one side but the hole looks centered. Well, here it is(bare) next to an M445(shiny). Hard to tell from the pic but this thing is crazy looking!

[Jamey]

that sucks it is off so much. Mine was almost perfect out of the bag. Wow nice polishing job on that octura!

[Turbo Dan-O]

Okay, just got back from trying out the 1715-17-45 on my Pursuit. I'm not finished with the S/B job yet but it was close enough for some 4S passes. Have not touched the boat since the last(and best) runs with the M445 and the water tonight was very close to the same as it was last time. Also did a back to back test on the Nano Techs vs. Revolectrics again.

Results:

M445/Nano Techs: 47.4 mph
M445/Revos: 50.2 mph

1715/Nano Techs: 48.0 mph
1715/Revos: 51.0 mph

Just like you guys have been saying, the ABC slips quite a bit but picked up a little bit of speed and also came in cooler. The Revos are just awesome! +3 mph and even cooler temps with them.

I took it back out again and beat on it pretty hard for a while. It ran great and everything still came in under 100*. I'm amped up and my boat is amped down!

[rayzerdesigns]

Just got in this 1715-17. It's waaaay heavy on one side but the hole looks centered. Well, here it is(bare) next to an M445(shiny). Hard to tell from the pic but this thing is crazy looking!

the 5 I have have all been really heavy on 1 side

[dasboata]

Guys I have a nice supply in stock I get them balanced just fine PM or email me if interested at dasboata@aol.com thanks Chris

[rayzerdesigns]

Hey I'm running a occurs x450 detongued a bit on my p mono what would be a good prop comparable to that to try

[dasboata]

Hey I'm running a occurs x450 detongued a bit on my p mono what would be a good prop comparable to that to try

I would try the 2014-2016 even a 1916 Ray