Rulebook anywhere???
Rulebook anywhere???
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
Nope. That's only IMPBA 1:8 scale. I don't think they do 1:10 in IMPBA. I doubt we'll ever get enough to worry about it.
We will have multiple years of the Oberto though.
Let's see if they show up first.
Noisy person
yes tom--some clubs on the west coast do just that and you must register each season if i'm not mistaken. someone please correct this if i'm wrong!
So, IF there is no formal "Rule Book" could I build a 1/10th hull and paint it as I see fit (keeping it in the "spirit") of the real hydros?
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
Depending on the club you have to run a minimum number of races to hold your boat registration. I think you can pay a fine to keep your boat registered if you can't make the 4 os races.
Sent from my SGH-M919 using Tapatalk
"Our society strives to avoid any possibility of offending anyone except God.
Billy Graham
Not to sound too pessimistic but we've been threatening to run scales since they hit the rule book. We've yet to see 3 show up. Let's get them in the water and see if we can turn some laps. I don't care if there are 6 budweiser hull.
Noisy person
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
OK...now we are getting somewhere...
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
We started running 10th scale a few years ago in sw fla and the spring shoot out by the wave blasters. Got about 6 boats now and are a blast to drive after u get them set up
Each club can put there own motor rules for each class we use the 1500 for both classes but thinking about 1800 for moderns
MY RETIREMENT PLAN?????.....POWERBALL
74 vintage kirby clasic hydro, pursuit mono, mg, 47'' mono, popeye hydro...
Some 1/10 Scale NAMBA boats are built so accurately to scale that you can actually hear the driver fart : (listen at 0:37)
https://www.youtube.com/watch?v=SLOD_9vx8HI
2008 NAMBA P-Mono & P-Offshore Nat'l 2-Lap Record Holder; '15 P-Cat, P-Ltd Cat 2-Lap
2009/2010 NAMBA P-Sport Hydro Nat'l 2-Lap Record Holder, '13 SCSTA P-Ltd Cat High Points
'11 NAMBA [P-Ltd] : Mono, Offshore, OPC, Sport Hydro; '06 LSO, '12,'13,'14 P Ltd Cat /Mono
Good one tony. My driver is too afraid of drowning to fart
MY RETIREMENT PLAN?????.....POWERBALL
74 vintage kirby clasic hydro, pursuit mono, mg, 47'' mono, popeye hydro...
That reminds me......if any of you locals are following this thread, how about some scorpion motors?
Noisy person
By locals I meant the club guys. Should I just pick the motor or should I ask the guys that want to run it?
Noisy person
i'm not building any more boats for the coming season-i'm doing five now and that's way to many.can't see doing another unless it's petes design!
It looks like ya need to read the rule book before ya build one of these boats ?
This is not all of the rules, so please read the rest. http://www.namba.com/content/library...a_rulebook.pdf
Hope this helps ?
T.C.
7. ELECTRIC 1/10 SCALE UNLIMITED HYDROPLANE
a) General Rules
i) The intent of this class is to replicate the look and competition of real unlimited hydroplane racing. Boats are 1/10-scale replicas (one inch
equals 10 inches) of the real boats that have raced on the unlimited
circuit. This class shall emphasize scale accuracy.
ii) Electric 1/10 Scale Unlimited Hydroplane rules will follow the Scal Unlimited Hydroplane rules (see Section 21) with the exception of the
following.
iii) Electric 1/10 Scale Unlimited Hydroplane rules are intended as a supplement to the Electric General and Sport Hydro rules. In the case
of a conflict with the Scale Unlimited Hydroplane rules (see Section
21) the Electric rules will prevail.
I copied this fron section 21..........
C. HULL SPECIFICATIONS
1. All boats will be models of past or present Unlimited Hydroplanes that are listed on
the Scale Unlimited Hydroplane Master Hull Roster.
2. Boats are to be built on a scale of 1½ inches equals 1 foot of the actual boat (1/8th
Scale).
3. The true scale dimensions of any Scale Unlimited Hydroplane will be derived from
the unlimited dimensions listed on the Scale Unlimited Hydroplane Master Hull
Roster. Boats will measure within the following tolerances of the true scale size,
excluding appendages.
a. Overall Length ……………………………... ± 1 inch
b. Beam…………………………………….……± 10%
c. Maximum Depth……………………………...± 10%
d. Afterplane Length (three point design)….……± 10%
e. Tunnel Width…………………………………± 10%
4. Boats will be painted, configured, and detailed like the actual unlimited as it ran on
the water. The acquisition of documentation validating a paint scheme, cowling
configuration, engine configuration, or other scale details will be the responsibility of
the boat’s owner. Photographs of the boat are an acceptable form of documentation.
5. Boats will enter competition complete with cowlings(s) and driver(s). If any of the
removable parts fall off the boat during competition, except as a result of a collision,
that boat will be awarded no higher than sixth place points in that round upon
completion of the heat. This penalization only affects the points that are awarded and
not the finishing placement of the boat which incurred the infraction. The placement
of and points awarded to other boats in the heat are not affected by this ruling.
Section # 21
Page # 3
Section Name:
SCALE UNLIMITED HYDROPLANE
Last edited by T.C.; 12-21-2014 at 10:15 AM.
http://www.hydromarine.de/
I noticed they make some 1/10ths as well.......
Not sure if they would be legal..
Grand River Marine Modellers
https://www.facebook.com/search/top/...ne%20modellers
terry, you gonna have it done in time for winter warmups?? what classes are you gonna run??
I'm hosed. I have a big project for Delta Air that will take me to Atlanta for 2 to 4 weeks. I leave this Sunday. So zero time to work on anything. Plus, my wife will be less than thrilled if I get right on a plan at the end of that adventure to go racing. ugh Gotta make hay and the sun and what ever that old saying is.
Tom is working feverishly on a scale though. Saw the progress last night. He should be ready for you guys.
Noisy person
At least you will be able to see that yellow glowing thing in the sky when you are down there! I think I remember what it looks like.
I'm really stupid here so bear with me... If I have a scale hydroplane hull that is 30.31" long x 14-3/4" Wide is there any modern scale hydroplane that this would be close to scaled up 10 feet per inch? How would I find out?
Nortavlag Bulc
Ray here is the ERCU Master hull list
http://e-rcu.com/resources/forms-documents/
"Our society strives to avoid any possibility of offending anyone except God.
Billy Graham
Thanks Jim, I'll bookmark it this time.
Nortavlag Bulc
If you know approximately what your hull resembles that's where you start. Then you check dims against the scale roster. The roster is here. It's on the scale pull down at the top of the page.
Typically guys go the other way and start with the roster and build accordingly. More often than not you find a hull you like and build it from Newton plans or have a frame set laser cut by someone that has already done the hard work like ML has. Getting from Newton plans to a working frame set is a bugger. Used to be at least. The plans were hand drawn and are more ideas than exact. You had to have a little imagination to make it work. Not a criticism. Some of the plans are ancient. I haven't tried it from scratch Newton plans in a while. They may be a cleaner gig these days.
Noisy person
This TFL hull looks very close to fitting the U-1 Miss Elam Plus 08' . I just don't know the sponson depth. Of course there would be a fair bit of changes I'd make to it but, to try and stay on a budget....
I asked for a bottom shot but, I have not got one from HOR. I'd have to talk to Monica if I wanted one or Tom C. maybe...
What do you think Jim?
Nortavlag Bulc
"Scale" models are a WHOLE different ball game. The spirit of scale model boats requires a different mindset and commitment than you typical model boat. This document should have the original hull dimensions that need to be maintained... (you will need to calculate for 1/10 scale)
http://www.namba9.net/NAMBA_MHR.pdf
Later,
Ball
Bookmarks