Paddy you are retired and it's 4 years till you are retarded mate. That dementia must be setting in early. Ha Ha I make myself laugh sometimes.
If the m447 is OK how about a detounged x645 with a little cup to reduce lift?
Paddy you are retired and it's 4 years till you are retarded mate. That dementia must be setting in early. Ha Ha I make myself laugh sometimes.
If the m447 is OK how about a detounged x645 with a little cup to reduce lift?
Know I got 6 boats last year and I have not had the time to put one in the water and now I'm off for my 4 week fishing trip and when I get back I get knee surgery and then it will snow again some time in september looks like Mr Krabbs is going to have to sit on the shelf
Rick
Send me a PM. I normally get sent raw props and $25.00 . They get sharpened and balanced and posted back Aust Post inc. For international it is still $25 Aust plus actual shipping costs. Cupping is free.
Just had a look in the prop box and I do have a M645, Send me a PM
Hi guys,
I am very pleased with the results of my mr Krab, where I participate in the Italian championship Hydro 2 and 3
Greetings from Firenze
Massimo
Special thanks a Steven Vaccaro..... my Supplier Reference
http://www.youtube.com/watch?v=tud1_F7kqew
http://www.gigapower.net/core/news.php?extend.4
Last edited by Hydro3; 08-02-2009 at 06:40 PM. Reason: don't upload from url
Several boats in various stages of destruction
Hi all,
Andym thanks for the x645 you sharpened and balanced for my XS3 it ran awesome with less hop and more drive.
the XS3 ran 96 kph until i hit something in the water and bent the rudder and dinged(bent) the prop. Hope i can repair it .
Im running 0 degrees advance on AndyG's advice to get a good setup before winding up the advance for top end.
AndyM i could shave with this prop it that sharp!!!!
SimonO what prop did you run on your XS3 wooden weapon????
STUFF NITRO GO LIPO FASTELECTRICS.COM
OFF-SHORE-ELECTRICS.COM
INVENTOR OF LITHIUM CELLS:bowdow
Send it back and I will happily have a look at it, unless it is cracked or really bent up the fix OkAndym thanks for the x645 you sharpened and balanced for my XS3 it ran awesome with less hop and more drive.
the XS3 ran 96 kph until i hit something in the water and bent the rudder and dinged(bent) the prop. Hope i can repair it
thanks Andy.when i receive my other props ill send to you for a rework.what type of balancer do you use?
what would be the best 4S fiegao to run in a mono or hydro with runtime/preformance?
SimonO wheres the video of your wood crafted XS3?
STUFF NITRO GO LIPO FASTELECTRICS.COM
OFF-SHORE-ELECTRICS.COM
INVENTOR OF LITHIUM CELLS:bowdow
I am using a Kintec balancer at the moment, the motor question depends on what hull, 7 & 8xl are good rigger/hydro mototrs up to about the 30" mark, the mono will depend on what size hull. Under 30" a 8 or 9 xl over that and I would look at a 580 size motor.
Just my opinion of coarse
I've been following this thread for about a year now...did anyone get these riggers to stop hopping and start handling?
If you want to stop jumping uses propellers abc or octura M series.post a photo of your Krabbe setup,angle of attak ecc ecc, so I can better advise
Massimo
Hi, i has bought a Dr. Super Evil, and i would like how monted this boat, angle to prop. Thank you.
I will use:
Leopard 3674. 1500kv
etti 150 opto with cups
5s lipo nanotech 6000
Prop 41mm etti, octura M540
I know this is an old thread but I've been working on an xzess III and thought some might enjoy an onboard video. The boat is running 63 mph just on initial setup. The video gets good at about 1:55 into it.
http://youtu.be/vBEJG_JEC4g
Last edited by mikef18; 04-19-2013 at 08:33 AM.
Bookmarks