Looking at buying a zonda thought i would see whats here?
Looking at buying a zonda thought i would see whats here?
Whats ur budget? I have a VIRGIN Keith Bradley built CF Daytona twin drive with Hyperion outrunners.This boat was built just over a year ago and has been a display for me. I will advise,if ur new to FE, this is not the boat for you. It will require soldering of the esc and motor bullets and flat spots ground in the motor shafts. ESC is a new Fc Twin 240 with the field programmer.Again.everything is NEW,NEVER wet not even in a bath tub! If you would like to see it,i'll upload pics in this thread(its the boat in my avatar)
001.jpg002.jpg004.jpg005.jpg006.jpg
A few pics for you to see it. As you can see,options were left open for upgrades.If you dont like outrunners,all the plumbing is done for the inrunners. This is a truly sweet Daytona. Can take more pics of anything you want to see and i stand behind anything i will ever sell on this forum. Mark
Forgot to mention,this hull had the optional epoxy coating on the inside plus Keith did his magic with CF inlay over that.
Last edited by h2o 1; 04-29-2013 at 08:45 AM. Reason: more info
I like your Daytona. It does seem like a sweet setup. Very interested in talking with you on this.
Would like to talk more with you on this Cat.
Todd, there's a build thread on this boat on the FC forum under Marks Daytona by Keith Bradley. Check it out. Thanks man,Mark
I want it. inexperienced with the air cooling. What was your setup ideas on the boat?
When this boat was built my target speed was a modest 50mph.I wanted a scale looking boat with scale speeds. These motors are made by Scorpion for Hyperion.Outrunners made by Scorpion are top quality and can take more heat than any outrunners on the market without demagnetising and permanent power loss. I was going to run this 4s2p. Props are x442 Cnc heat treated. The only flaw on this boat is the corner of the windsheild sticker is slightly peeled due to my dusting and wiping once a week. Mark
008.jpg
Here the sticker i spoke of.
009.jpg010.jpg011.jpg012.jpg
Heres a few more Todd. Please note before you commit to this that this hull is exactly as i got it back from Keith other than a few added small pieces. Keith did not wrench any of this hardware super tight due to my instruction.My intentions was to eventually have this hull painted was the reason behind that. I was undecide on the battery trays or velcro so i never epoxied them down.You will have to tighten the hardware and seal this hull. Just so you know bro,no surprizes! Mark
This is what you will get Todd
FC Daytona hull with CF inlay by KBB
Custom CF motor mounts by KBB
Custom CF stuffing tube supports by KBB
Custom servo mount by KBB
Custom esc cover by KBB
KBB hatch bolt kit installed
2x Hyperion 3026 1900 kv outrunners
2x 110mm 3/16 stinger drives
2x Aeromarine flex cables,L&R
2x Aeromarine 3/16 collets
2 CR x442 aluminum props
2 long battery trays
Fightercat 240 Twin esc with programmer and all connectors for your batts and motors included
Kintec center mounted rudder 110mm
Everything in these pics is what you will get incase i forgot something. Hope this helps.
This system was setup to run 4s as i understand? will it take 5s, 6s? Too much?
The motors are rated at 5s but i was only going to use 4s correct.I wouldn't personally run this on 5s,like i said top speed wasn't a factor.Play with it on 4s bro,im sure with testing and the right props it will surely be a pleaser.
Payment sent. Shipping in notes. Please let me know when you receive it.
Got it Todd! Will ship in the morning and i'll pm you the tracking number.Ur gonna love this one bro,once its in your hands, you will see exactly why it was my flagship of shelf queens! Its that damn pretty!! Thanks again Todd,Mark
Todd what connectors do you want with this? The esc has pre installed 6mm bullets on the motor side and spares for the motors. I have 5.5,6.5 and 8mm bullets for the batts. Whichever you choose i will send you plenty! Mark
I think 6.5 will work good. Anything you want to send along would be much appreciated! Thanks so much for the great communication and information. I look forward to putting this one together. No shelf queens here, it is going to water! I may hit you guys up for some setup info......... Thanks Mark!
Oh, and yes tracking number please!
Will Do!I hear you on the getting it wet,i've had my share of cracked hulls and i didn't want to see this one in misery!lol! Thanks again Todd, TTYS,Mark
I'll send the tracking number via pm tomorrow morning when this ships from the PO.Dont worry bro,i've sold and bought many things on this forum and like i said,i stand behind everything i sell.
Nice looking boat man!
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
Thanks guys! This one has a new owner. Congrats Todd!! Hmmmm,i wonder what will replace this one? Keith if ur reading this i'll be in touch soon.
013.jpg
Here you go Todd,all boxed up and ready to ship! I will send this very insured so when you get this box delivered to you please check it for ANY damage. And if theres a single dent in this box open it in front of the driver, that really helps if i have to make a claim. I also included a few freebies for you,enjoy this bro! TTYS,Mark
You Rock! Thanks for all the attention to the boat! I will keep you posted on progress. Can not wait to see it!
SHIPPED TODD!! sent you the tracking via pm. ETA thursday 5/2/13. Its was a pleasure working with you and have fun with this bro! Thanks again and keep in touch,Mark
Your awesome and super helpful! Thanks for the prompt shipping! I will let you know when it arrives! Thanks so much! Todd
Packaging by NASA! Good job, on the box up, no damage at all! Boat looks awesome, just what you said it was! Thanks to Mark for being a great guy to buy from and taking care to ship everything right!!!! Thanks for the little extras you threw in too mark!! Yeah me!
Glad you like it Todd! Thats a sweet Daytona for sure! Again bro it was nice working with you on this. Take care of that one Todd. Thanks again man,Mark
20130505_173351.jpg Time to get to work!
20130505_172044.jpg Had a DJ laptop stand that doubles as a boat stand.
Bookmarks