Experience with a Turnigy T5692 1320KV motor???

[JIM MARCUM]

Anyone out there have experience running this motor? I have a brand new one & am considering using it in my Aeromarine Avenger cat build, 8-10S. I have used Leopard 5692s with excellent results, but couldn't pass up the T5692 1320KV for only $80. It appears to be well built & has a larger shaft than my Leopards, but other than the opinions by OSE guys who don't own or have ever ran one, I haven't read how well this motor works out in actual use.

Is there anyone out there who has experience running this motor & how well it performs? RSVP JIM

[oscarel]

Yes Jim, I'm running 2. This is from a run this afternoon. I was running 7s1p per motor using Castle Ice esc's, turning X457's. I ended up breaking one of the .187 shafts. 65mph per Eagle Tree. These have replaced the 1717's I was running on 6s2p which was pulling spikes of 300 amps.

castle 200 7s1p.jpg

[JIM MARCUM]

So you like yours, Oscar? I would run 1/4" flex drives Oscar, 3/16" would be puching it. The Eagle Tree spikes indicate (to me anyway) that you need to install capacitor banks on your ESCs to reduce the feedback ripple. Here's what OSE has: http://www.offshoreelectrics.com/pro...i-e041&cat=136. If you want to build your own cap banks, I bought 16 Rubycon 35W 1500uF ZLH caps either on Ebay or with a web search (can't remember which). Was on a cap buying binge & bought others, but the Rubycon ZLH series is the best to limit ripple current, according to some really smart OSE guys. Any major brand - 5-6 caps each - with >35V 1500uF will work better than only the Castle's. If you are not running the new Castle Hydra ICE2 HV 200A ESCs send them to Castle for a no charge upgrade. I blew both of my "old" style Castles. JIM

[oscarel]

I've got extra caps and they only help with ripple which is only about 1 volt. I have Rubycon ZLH, 2-1000's and 2-470's extra on each. Yes, so far I'm very pleased with them. I'm going to put CR X452's on and run it on 6s once I get the shaft replaced to compare with the 1717's. I know they're bigger motors but the fact I'm getting almost the same speed with less amp draw and also now being able to only run 1p makes it worthwhile. I do have the ICE2 version and I'll eventually switch over to 1/4. I haven't removed the old shaft yet, but it looks like it split where I had a homemade oiler on the shaft.

[oscarel]

Just looked at esc, I actually have 4 of each cap.

[JIM MARCUM]

Cool. I've been running X6xx props and the extra pitch helps. Also gonna try out the 19xx & 21xx series for even more pitch. But, I'm building SAW cats. JIM

[Make-a-Wake]

I own a 5692 in the 1000kv model. I run it in a 39" Racemaster on 8s.................works well so far and sounds very different..........real cool.

[Brushless55]

Yes Jim, I'm running 2. This is from a run this afternoon. I was running 7s1p per motor using Castle Ice esc's, turning X457's. I ended up breaking one of the .187 shafts. 65mph per Eagle Tree. These have replaced the 1717's I was running on 6s2p which was pulling spikes of 300 amps.

castle 200 7s1p.jpg

What packs are you using to only need 1p
thanks

I own a 5692 in the 1000kv model. I run it in a 39" Racemaster on 8s.................works well so far and sounds very different..........real cool.

I was thinking of trying the 1320kv version for 6s runs in my DF39
need a mount before I buy the motor...

[oscarel]

What packs are you using to only need 1p
thanks



I was thinking of trying the 1320kv version for 6s runs in my DF39
need a mount before I buy the motor...

Turnigy 5000 40c. I'm running one set per motor.

[Brushless55]

Turnigy 5000 40c. I'm running one set per motor.

Great, thank you!

[lenny]

Hey,
Member Coolmind is running one and doing some testing,
He had a video up, But its not working now.
I sent him a pm to post in ose videos.
Link to thread, Post #12 https://forums.offshoreelectrics.com/...-Mono-(DF-MKII

What packs are you using to only need 1p
thanks



I was thinking of trying the 1320kv version for 6s runs in my DF39
need a mount before I buy the motor...

[Mel279]

hi

I have run 2 Turnigy 5682 1050kv, 10s in my twin cat epv135, getting a topspeed 76mph. FYI its a 6 poles motor not 4 poles. So is it ok if I use higher timing? and what is the function of adding additional cap's on esc?

[Espresso]

hi

I have run 2 Turnigy 5682 1050kv, 10s in my twin cat epv135, getting a topspeed 76mph. FYI its a 6 poles motor not 4 poles. So is it ok if I use higher timing? and what is the function of adding additional cap's on esc?

So in this video you're running a 12S setup? http://www.youtube.com/watch?v=3pTWO...1&feature=plcp

What's speeds are you getting vs the 10S? For a big boat like this, it really moves and has a huge rooster tail. Twin 5682 and twin Swordfish 240A? Do you have a data logger to see what amps you're pulling?

[lenny]

Hears Coolmind boat,http://www.youtube.com/watch?v=xnkGl...1&feature=plcp

[Rumdog]

8-10s?? I'm hoping this is a SAW only app.

[Magus]

Hello,
I want to use 2 T5692 1320kV motors on 2 x 6S (6S1P per motor) with Tnrugy 180A esc. And if there is not enough power, I will upgrade to 8S.
I've read, that someone use the T5692 with 10S? Is that correct? At the hobbyking site is marked, that the motor only runs with 8S max.

Best regards,
Birger

[Brushless55]

Hello,
I want to use 2 T5692 1320kV motors on 2 x 6S (6S1P per motor) with Tnrugy 180A esc. And if there is not enough power, I will upgrade to 8S.
I've read, that someone use the T5692 with 10S? Is that correct? At the hobbyking site is marked, that the motor only runs with 8S max.

Best regards,
Birger

That a big amount of power
if you want to run 8s or 10s choose a lower kv motor..

[Drax21]

I plan on putting a 5692 1000kv in my DF41 on 8s. HK are out of stock though as usual. These sold out fast. Funny how they still have stock of the 5682 version but the 92 version says 1500 more watts of power.

[Magus]

@Brushless55: I hope, that the two T5692 are powerfull enough, else I will change to 8S.
I've got two Turnigy 180A esc up to 6S, so at first, two engines at 6S have to be enough.
Thats the reason, why 1320kV.
1000kV@6S are only 21600rpm and I like a little bit more

[Brushless55]

@Brushless55: I hope, that the two T5692 are powerfull enough, else I will change to 8S.
I've got two Turnigy 180A esc up to 6S, so at first, two engines at 6S have to be enough.
Thats the reason, why 1320kV.
1000kV@6S are only 21600rpm and I like a little bit more

What's your goal speed wise with the 1320kv motors on 6s?
and running 6s on the 1000kv motors is a bit low IMO...

[Mel279]

So in this video you're running a 12S setup? http://www.youtube.com/watch?v=3pTWO...1&feature=plcp

What's speeds are you getting vs the 10S? For a big boat like this, it really moves and has a huge rooster tail. Twin 5682 and twin Swordfish 240A? Do you have a data logger to see what amps you're pulling?

I've use different motor for 12s and 10s. 12s setup, I've use leo 5692 730kv and 10s would be turnigy T5682 1050kv. In term of speed, for 12s I've only manage to get around 60mph and 10s around 76mph. I don't have any datalogger so I have no idea how much amp that it pull.

[FRED]

Gents; 1320 on 6s gives you 29220 rpm. with a decent prop.-------I was reading on caps; buy a cap bank. I use same size caps from Minnesota and fast service. I try and use smaller caps than 1000 as the smaller caps which takes many caps dissapate heat faster. Buy a bank and remove existing caps but you can keep existing caps and solder same size # on existing caps and solder bank on the the power wires. Nows here's the catch, it makes esc more combursome to place in boat. Now there was a guy who soldered caps 3 high and cap wires had the covering off servo wires to cover 3 high wires so shorting wouldn't occurr. I do that when i change or add caps. I know it sounds like i'm half a bubble off but never a problem, I also sand my fets flat so all the fets work and get cooled.

[coolmind]

As you can see the way i play in the video with 2x6s 5800 mha parallel(6s 11600mha)i got around 20 min of playing time.And the prop is prather 240(53,8mm Diameter and 3,3 pitch).The motor can handle a larger prop(prather 245)on my setup,i will test it and give you the results .

[Magus]

@brushless55
The target is, with a realativ low-budget setup, to get the most speed possible
What do you thing, how fast ist realistic?

[Brushless55]

@brushless55
The target is, with a realativ low-budget setup, to get the most speed possible
What do you thing, how fast ist realistic?

What hull are you using?

[Magus]

EPV 135 hull

[Espresso]

@brushless55
The target is, with a realativ low-budget setup, to get the most speed possible
What do you thing, how fast ist realistic?

I think the answer should be in the lines of this below since you're using the same hull. Just depends on the exact KV and lipo setup. Mel's cat looks pretty fast in the video but he said that was only ~60mph. I'm not sure if he has a video of it going 75+. Pretty impressive.

I've use different motor for 12s and 10s. 12s setup, I've use leo 5692 730kv and 10s would be turnigy T5682 1050kv. In term of speed, for 12s I've only manage to get around 60mph and 10s around 76mph. I don't have any datalogger so I have no idea how much amp that it pull.

[Brushless55]

EPV 135 hull

Twin 1320kv on 6s should push your hull into the 60's for sure

[Mel279]

My epv135

[Magus]

very nice!!! Really impressive
At first 60mph are really ok, but für future, I hope to reach 80-90mph And up to 100mph, but than I need Lehners...

I think, you know the vid from Timo Heinrich with topspeed above 180km/h

Timo Heinrichs setup: LMT 3040/6 (diameter 60mm / length: 80mm / 1750kv ) and Schulze 333WK
My problem: The Lehners and the HV esc are to expensive

I have 4 x 3S1P 5000 45C and 2x Turnigy 180...