CLONE Skunkworks Gen2 Cat?????

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • srislash
    Not there yet
    • Mar 2011
    • 7673

    #31
    Just poking around. Helping someone else with an issue.I was just bugging Ray,I did the CF.
    I had thoughts about painting Jason's MG but I have to work tomorrow and if I start...

    Comment

    • tagasagwan
      Molino Boater!!!
      • Jun 2008
      • 990

      #32
      Originally posted by srislash
      Just poking around. Helping someone else with an issue.I was just bugging Ray,I did the CF.
      I had thoughts about painting Jason's MG but I have to work tomorrow and if I start...
      Hahaha! You got me there buddy! I told Ray about the 37" cat that we are chatting about on the other thread! I'll drop by Macdon's place later so, I'll keep an eye on that one and the Cig boat too!
      My Aquacraft SV27's old Video: http://www.youtube.com/watch?v=VoTm4Btz41Q
      MHZ Micro Iceberg, Skunksworks Gen2 Cat twin, Aquacraft SV27, SM29 1515 sold.

      Comment

      • Heath M
        Senior Member
        • Mar 2008
        • 806

        #33
        Theres one here in Aussie to, bought it from Scott in 07, sold it in 11. Big mistake, definitely my favourite boat, was a missile with 1515 1y 4s1p and a mod m445 prop.
        http://youtu.be/Xr1frWqlRpE
        Brisbane,QLD, Aussie

        Comment

        • tlandauer
          Fast Electric Addict!
          • Apr 2011
          • 5666

          #34
          Originally posted by egneg
          I have twin Aveox 36/30/1.5 motors with T120 ESC's. I have the Venom 36mm cnc props at present but am prepping a pair of 38mm/2 props from Fighter Cat.

          [ATTACH=CONFIG]67418[/ATTACH][ATTACH=CONFIG]67419[/ATTACH]
          I got a pair of Etti drives from you along with two counter-props, were these used with this boat? I am thinking of a H&M Intruder S twin build and have a question regarding your opinion on the .130 cable and 4mm shaft that was on that set. Are they good to handle FC 3216 Outrunner (2200kv on 4s) ?
          Too many boats, not enough time...

          Comment

          • egneg
            Fast Electric Addict!
            • Feb 2008
            • 4670

            #35
            Originally posted by tlandauer
            I got a pair of Etti drives from you along with two counter-props, were these used with this boat? I am thinking of a H&M Intruder S twin build and have a question regarding your opinion on the .130 cable and 4mm shaft that was on that set. Are they good to handle FC 3216 Outrunner (2200kv on 4s) ?

            Yes they were. I am not familiar with this hull ... what size is it?
            IMPBA 20481S D-12

            Comment

            • tlandauer
              Fast Electric Addict!
              • Apr 2011
              • 5666

              #36
              I sent the hull for CF lay up, I think it is 30" or there about.
              IntrudS08.jpgThe smaller one... 750mm length.

              Thanks in advance!
              Too many boats, not enough time...

              Comment

              • egneg
                Fast Electric Addict!
                • Feb 2008
                • 4670

                #37
                I think you will be good, the skunk was 32 inches.
                IMPBA 20481S D-12

                Comment

                • tlandauer
                  Fast Electric Addict!
                  • Apr 2011
                  • 5666

                  #38
                  Originally posted by egneg
                  I think you will be good, the skunk was 32 inches.
                  Thank you very much!
                  Too many boats, not enough time...

                  Comment

                  • Santig
                    Member
                    • Nov 2019
                    • 79

                    #39
                    I know this is an old thread, if you gents are still around, is this a Skunkworks gen 2?s-l1600 (2).jpg

                    Comment

                    • Santig
                      Member
                      • Nov 2019
                      • 79

                      #40
                      I hate to revive an old thread but haven't found much info on this boat. Is this one of the original skunkworks?

                      20191218_193958.jpg

                      Comment

                      Working...