Results 1 to 29 of 29

Thread: blackjack or sv (brushless)

  1. #1
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default blackjack or sv (brushless)

    lots of good info on this site still cant decide.I will run lipo's on either one.I have a villain 7.2 now and want to move up. thanks.

  2. #2
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    I have both, they are both fun and fast ... IMO the SV27 handles better in the turns out of the box... The BJ26 handles rough water better out of the box.... I was not really happy with the BJ26 until I did a hardware upgrade .. That made it a wonderful little kitty!! Each hull has its up's and down's....Both will blow your Villain 7.2 right out of the pond!!

  3. #3
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    the thing is i dont want to do an upgrade right away.i put some money into a charger (bantam bc6)for lipos so i can use it for the boat and some cars. saying that what do you think as far as the boat goes? also for $400-$500 could i build a boat with no experience(brushless).thanx this site is graet.

  4. #4
    Join Date
    Sep 2007
    Location
    CA
    Posts
    502

    Default

    It depends on the size of the boat and what speed u are looking for. Here a hull can cost inbetween $80-$675 its all up to u in how much u spend. A premade hardware system can cost $50-$95 or a custom system can cost u probably $60-$90 and Props are $5-$45. And a Brushless ESC will run from $23-$255 and a Brushless motor will run $60-$400. But if u want a premade Brushless system heres one. But remember its up to u on how much u spend and how much u want to put in the boat.
    Failure is the First step to SUCCESS

  5. #5
    Join Date
    Apr 2007
    Location
    Nj
    Posts
    4,735

    Default

    Mat any boat is what you make it. The question is not whats better but what do you like??? Do you like Cats, Mono's or hydros? Once you figure that out then you can look into what hull or rtr setups best for you. :)

  6. #6
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    tanx for all the links and info. i will look into a build with a mono hull that can get into the 30-35 mph range.may take me a while but its winter so i have the time. also i would like to get a hull that is 35 inch or so, ose looks to everything i will need.

  7. #7
    Join Date
    Apr 2007
    Location
    Nj
    Posts
    4,735

    Default

    Good choice for a first boat. Good luck and be sure to ask questions before you buy or build:)

  8. #8
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    ok might have to move this do the build forum.delta force 33 or the aeromarine titan 33 look like what i would like.will the super v 27 brushless motor and esc work with this hull?maybe not the power it would need?

  9. #9
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    You would be happy with both 33" hulls. The SV27 power system is not going to cut it for a hull of that size and weight.. Look at Feigao 11XL and 12XL, they will work w/ those hulls...Mabey a Hydra 120 esc or OSE has new 100A esc's w/ usb programmer (somewhere around $100) that should be on the site soon...

  10. #10
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    You will learn alot and be more happy in the end, building one of these 33" V-hulls...They will handle rougher water and be more stable overall compared to the SV and BJ...

  11. #11
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    cool what about the speed master mono for the hardwere?sorry for all the ?just need to get an idea of the things i will need so i can figure out the budgrt.hull $140-170.hardwere $100 electrics?

  12. #12
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    ok 10xl $70.00 xpower 70 amp $65.00 will that speed control work for this motor

  13. #13
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    sorry 11-12 xl

  14. #14
    Join Date
    Apr 2007
    Location
    Nj
    Posts
    4,735

    Default

    The speed master HW is very nice and quite user friendly to install. I would not go with the 70 amp esc. Go with the x100. You always want some head room. I would run a 9xl on 4s-2p or 12 nimh. That should give you a 40mph+ boat.

  15. #15
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    Go with the 100Amp!!I have run a 11XL in the Aeromarine Titan 33" with a Hydra 120 and X447 and X645 with speeds of 44-48mph.. The Titan is a pretty heavy with 4S2P 5000's, the 11XL will allow you to run a large prop w/ less amps and heat!

  16. #16
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    sounds good for th esc (100amp) why the 9xl and not the 11-12?what is the difference rpms?

  17. #17
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    what about the hardwere?

  18. #18
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    Speedmaster is great, OSE has it in stock most of the time!!

  19. #19
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    9XL will turn more rpm and be faster with the same prop.. But it will pull more amps.. Be careful when running these esc's, keep the average amp range at around 70% of Max amps on the esc!!!

  20. #20
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    ok cool i think i will order the hull and hardwere fist. i think i will also call or email ose and let them know what i want to do so i can get all i will need.tanks alot guys.

  21. #21
    Join Date
    Apr 2007
    Location
    TX
    Posts
    1,711

    Default

    Has anyone run the SV and Blackjack motors in the same hull for a comparison?
    ReddyWatts fleet photo
    M1 Supercat - Neu 1527 1Y, 8s / Mean Machine- Feigao 580, 8s, 120 HV esc
    Mean Machine - Feigao 540 14XL, 8s, 100 amp HV esc, X537/3

  22. #22
    Join Date
    Apr 2007
    Location
    Nj
    Posts
    4,735

    Default

    No prob. Just be sure and go with a .150 drive cable. I think the set comes with it. If you want I can PM you a complete parts list so you dint miss anything.

  23. #23
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    cool i dont know how to do the pm. let me know . i alredy have a list in my wish list but know i am missing some stuff so that would be graet.

  24. #24
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    o ya did i mention i am VERY EXCITED TO DO THIS BUILD?

  25. #25
    Join Date
    Apr 2007
    Location
    Nj
    Posts
    4,735

    Default

    click on my user name and in the profile there is a private message user tab

  26. #26
    Join Date
    Oct 2007
    Location
    Wy
    Posts
    1,494

    Default

    Post some pictures in the Build Thread once you get started!!

  27. #27
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    ok sennt you a mesg. iwill do pics the though out the entire proses.

  28. #28
    Join Date
    Sep 2007
    Location
    CA
    Posts
    502

    Default

    If u want to contact OSE Steven Vaccaro runs it send him a message
    Last edited by Ocean Racer; 01-07-2008 at 10:21 PM.
    Failure is the First step to SUCCESS

  29. #29
    Join Date
    Jan 2008
    Location
    rockford il
    Posts
    15

    Default

    ok thanks............

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •