Results 1 to 16 of 16

Thread: Prop Diagram

  1. #1

    Default Prop Diagram

    Steven Vaccaro

    Where Racing on a Budget is a Reality!

  2. #2

    Default

    Broken tip on the left side?

  3. #3

    Default

    I used a new prop, so it wasn't broke. I think it's the way I took the photo.
    Steven Vaccaro

    Where Racing on a Budget is a Reality!

  4. Default

    Great explanation and picture Steve need to be in a Read this first Newbe and yes for everyone.

  5. Default

    Steven,

    Here is a copy of the latest Octura information sheet 9.2012 listing the Prop number, Diameter and then Pitch.

    Makes it easier for me to follow and then make a decision on which ones to order.

    Mike
    Last edited by Mike Caruso; 10-07-2012 at 07:39 AM. Reason: date

  6. #6

    Default

    can you email it to me or try to attach it again?
    Steven Vaccaro

    Where Racing on a Budget is a Reality!

  7. Default Octura New Prop list 9.12

    9.12 Octura prop list.jpg

    Here you go Steven

  8. #8

    Default

    Trying to find where to buy a b/s x440/3 I think it is a stainless steel for my Miss Geico 29 v3 all stock

  9. #9

    Default

    I just sent you a pm.
    Steven Vaccaro

    Where Racing on a Budget is a Reality!

  10. #10

    Default Miss Geico 29 v3

    I just received two Octura X440/3 props and both of them seem to have the same problem, they will not fit the drive dog.
    it seems that one side of the slotted end of the prop is misaligned and if I removed about 1/16" from one side on the leading edge it would fit, but would be out of balance. what would you recommend.

  11. #11

    Default

    Quote Originally Posted by Fixitguy1 View Post
    I just received two Octura X440/3 props and both of them seem to have the same problem, they will not fit the drive dog.
    it seems that one side of the slotted end of the prop is misaligned and if I removed about 1/16" from one side on the leading edge it would fit, but would be out of balance. what would you recommend.
    Do you happen to have a picture? Sometimes the slots have to be opened.
    Steven Vaccaro

    Where Racing on a Budget is a Reality!

  12. #12

    Default

    Quote Originally Posted by Fixitguy1 View Post
    I just received two Octura X440/3 props and both of them seem to have the same problem, they will not fit the drive dog.
    it seems that one side of the slotted end of the prop is misaligned and if I removed about 1/16" from one side on the leading edge it would fit, but would be out of balance. what would you recommend.
    Use a 5/16" (8mm) od drive dog.
    NZMPBA 2013, 2016 Open Electric Champion. NZMPBA 2016 P Offshore Champion.
    2016 SUHA Q Sport Hydro Hi Points Champion.
    BOPMPBC Open Mono, Open Electric Champion.

  13. #13

    Default

    Yep use the little doggy.

    >
    >

  14. #14

    Default

    Removing material from the hub has less of an effect on practical balance than you may think. Removing 1/16" from the slot sounds like way too much however...


    .
    ERROR 604 - Caller's Buffer Is Too Small
    1. Ensure that your port is not configured to a low speed
    2. If you are still having problems, contact your counselor

  15. #15

    Default

    The drive dog slots are fine the tongue material is covering the the drive dog slot on one only

  16. #16

    Default

    image.jpegimage.jpegimage.jpeg
    Hope you can see this.
    Attached Images Attached Images

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •