Page 2 of 2 FirstFirst 12
Results 31 to 47 of 47

Thread: Turnigy batteries - quality problems

  1. #31
    Join Date
    Nov 2007
    Location
    FL
    Posts
    6,927

    Default

    Remember, the Hyperions are already the "Nano" technology. They have been out for several months and proven to be outstanding batteries. Best part is they are warranted right here in the USA!

    We are a hyperion dealer. We offer a discount to OSE members. You need to PM me for a quote. The packs are NOT on our website.
    Mini Cat Racing USA
    www.minicatracingusa.com

  2. #32
    Join Date
    Jan 2008
    Location
    VA
    Posts
    3,070

    Default

    PM sent Jim.

  3. #33
    Join Date
    Jul 2010
    Location
    WA
    Posts
    121

    Default

    Well, I got my packs today from HK. Turnigy 4500 and 5000 2s1p. 3 of the 4 packs the balancer reads both cells, but one 5000 only reads 1 cell. put on charger and thankfully it reads 2s1p, but voltage was around 5.6 or so. it quickly came up even on 1C. May need to watch this pack. Im bringing it up to 7.7 to match the other, then charge them both at same time. I think Ill deal with the website that has them in the US after reading the horror stories. fwiw

  4. #34
    Join Date
    Feb 2008
    Location
    Va
    Posts
    4,670

    Default

    I have a 4S/5000 pack that always had balance problems but the voltages have always been good. I have used it hard (racing) all season with no problems.
    IMPBA 20481S D-12

  5. #35
    Join Date
    Jul 2010
    Location
    TX
    Posts
    119

    Default

    Add me to the list. Just got 2 3S 5000Mah 25C Turnigy packs and right in the middle of the first run with them, boat goes dead. Put it on the charger and during battery check says "Connection Broken".

    I got a return authorization and since I bought them in the US warehouse, I hope, but doubt I'll be able to return them state side.

    I'm done with Turnigy as well.

  6. #36
    Join Date
    May 2009
    Location
    ON
    Posts
    3,180

    Default

    Try with no balancer and low voltage as NmH for few minutes and when the voltage will get up a little just put it back for regular LiPo charging with balancer....
    It should fix the problem.... Make sure to monitor....








    Quote Originally Posted by ms71171 View Post
    Add me to the list. Just got 2 3S 5000Mah 25C Turnigy packs and right in the middle of the first run with them, boat goes dead. Put it on the charger and during battery check says "Connection Broken".

    I got a return authorization and since I bought them in the US warehouse, I hope, but doubt I'll be able to return them state side.

    I'm done with Turnigy as well.
    DJI Drone Pilot
    Canada

  7. #37
    Join Date
    Oct 2008
    Location
    CO
    Posts
    9,488

    Default

    Quote Originally Posted by ms71171 View Post
    Add me to the list. Just got 2 3S 5000Mah 25C Turnigy packs and right in the middle of the first run with them, boat goes dead. Put it on the charger and during battery check says "Connection Broken".

    I got a return authorization and since I bought them in the US warehouse, I hope, but doubt I'll be able to return them state side.

    I'm done with Turnigy as well.
    I've bought about 20 packs from HC and I did have one out of the group that went dead like yours in my brushless Revo.. come to find out it was a tap that the solder joint was bad.. I spent about 2min for fix the pack, and now it works great
    real easy fix
    .NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s

  8. #38
    Join Date
    Jul 2010
    Location
    WA
    Posts
    121

    Default

    After I charged the pack some, I was waterproofing and setting up the boat. I tried to see which one didnt read on the blinky. Well, now its registering on the blinky. wiggled wires and still fine. Ill still be monitoring these packs tho..
    Ron
    1/10th 2014 U-6 Oberto ,1999 U-6 Miss Madison, 1971 U-6 Miss Madison, 1976 U-6 Miss Madison Unlimited Hydros

  9. #39
    Join Date
    Jul 2010
    Location
    TX
    Posts
    119

    Default

    Quote Originally Posted by Brushless55 View Post
    I've bought about 20 packs from HC and I did have one out of the group that went dead like yours in my brushless Revo.. come to find out it was a tap that the solder joint was bad.. I spent about 2min for fix the pack, and now it works great
    real easy fix
    So you cut open the pack?

  10. #40
    Join Date
    Aug 2010
    Location
    NH
    Posts
    31

    Default lipo batt.

    My 1000 mAh 3c 11.1v 25c lipo batt. in my 26" Boat swells up after a run. I'm running a Fiego 7L 3511kv motor with a Caste Creations Hydra 120 esc . I'm new with RC Boats Please

  11. #41
    Join Date
    Dec 2009
    Location
    la
    Posts
    1,078

    Default

    1000 mah? Sounds like the problem lol
    Catching Air!

  12. #42
    Join Date
    Oct 2008
    Location
    CO
    Posts
    9,488

    Default

    Quote Originally Posted by gartman View Post
    My 1000 mAh 3c 11.1v 25c lipo batt. in my 26" Boat swells up after a run. I'm running a Fiego 7L 3511kv motor with a Caste Creations Hydra 120 esc . I'm new with RC Boats Please
    Welcome!
    one question, how long are you running your boat?
    also, that's a small battery for a boat that big with that motor
    .NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s

  13. #43
    Join Date
    Jul 2008
    Location
    NZ
    Posts
    954

    Default

    hahaha 1000mah!

    Lucky it hasn't caught on fire tbh. Not a quality issue with the battery in this case..

    Is it a 540 or 380 sized motor?
    Matt.
    FE, Nitro and Gas racing in Auckland
    www.rcboats.co.nz

  14. #44
    Join Date
    Nov 2007
    Location
    FL
    Posts
    6,927

    Default

    I'm amazed you haven't flamed that 1000mAh lipo! That motor must be pulling WAY more than that battery can handle. Sounds to me like you should have at LEAST a 3000mAh batt in there...maybe more. 26" boat will certainly handle the size and weight.

    How long are your runs....1 minute? ;-)
    Mini Cat Racing USA
    www.minicatracingusa.com

  15. #45
    Join Date
    Jul 2010
    Location
    PA
    Posts
    238

    Default

    Quote Originally Posted by gartman View Post
    My 1000 mAh 3c 11.1v 25c lipo batt. in my 26" Boat swells up after a run. I'm running a Fiego 7L 3511kv motor with a Caste Creations Hydra 120 esc . I'm new with RC Boats Please
    He has got to be Messin with everyone on this.....there is no way he could have run that at all !!!

  16. #46
    Join Date
    Jul 2010
    Location
    PA
    Posts
    238

    Default

    Received 6 lipos from Hobby King today, 2 4s 4000mah nano-tech's, 2 2s 4000mah nano-tech's and 2 2s 1550mah Rhino's

    all six are fine and UPS shipping from Honk Kong to Pennsylvania took less than 3 days including the weekend....Ordered friday evening and the UPS man delivered them Monday morning !!!!

    Shipping was $43.00 but divided by 6 Batts thats only $7.16 per Battery for Super fast shipping !!

  17. #47
    Join Date
    Oct 2008
    Location
    CO
    Posts
    9,488

    Default

    that is sweet!
    .NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s

Page 2 of 2 FirstFirst 12

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •