'82 Executone, '83 Speedy Blueprinting, '83 Miss Rock KISW 1/8th scale Hydro Builds

[TotalPackage]

Most RC boat racing is right turn oval.

Doesnt that mean the right sponson is the one you want planted while the left sponson slides?

[sailr]

Full scale races to the left and some orgs race the 1/8th scale to the left also.

[tharmer]

Not scale racing. The full size boats turn left.

[sailr]

That's what I said, FULL SCALE = FULL SIZE. I know there is an r/c scale organization out in Washington State I think that races to the left also.

[tharmer]

ERC-U for the 1/10th guys. (erc-u.com)
ESU for the 1/7th guys. (scalehydro.com)
-t

Our posts apparently overlapped.

[TotalPackage]

All the race boats ive seen have the driveline ,if offset, set to the right of the keel i was just curious mike?

[sailr]

The e-rcu.com is the correct link.

Here's some shots from the scalehydro.com site of their boats turning left!

[cybercrxt]

Now we are getting somewhere. The decals from Mike Mcknight should be here in a day or two, so the paintwork can begine. Enjoy, MIke

[sailr]

lookin good!

[Darin Jordan]

Looks really nice, but then you do REALLY nice work always... Will be interested to see how it handles... especially with the break that far forward in the tunnel...

[cybercrxt]

The break in the tunnel is where Roger put it in the plans. It has been run like that on many builds, and on the full size hull!

[TotalPackage]

Boy... I don't like all those curved surfaces on that thing... How big is this boat?

Darin heres a link tell me what you think:http://www.rcuniverse.com/forum/m_75..._2/key_/tm.htm

[cybercrxt]

I will be updating this thread soon. I have hte hull in primer now, and I am awaiting some magnets to arrive for the hatch. More soon! Mike

[TotalPackage]

looks great Mike

[racer504]

Have you determined a price for the 1/10 scale 8255 hull kit yet?

[sailr]

The main reason for shaft offset is to counteract torque roll. If turning right, the offset should be to the right. If turning left, it is offset to the left. This is because the rotation of the prop is the reverse depending on which way you are turning.

[cybercrxt]

Well, its been a while since I updated the build thread, but I have beendoing work on the boats. I got magnets installed in my deck and cowling, primed, and the white basecoat with SG100 HOK layed over so I can begin the artwork. If I was making the Miss Houston, I would be close to done! lol. The other two hulls are coming along too. Enjoy, Mike

[cybercrxt]

[JimClark]

Who is doing the graphics?
Jim

[cybercrxt]

Jim, Mike McKnight at ProMedia is. He does really nice work, and I think he can get as specific as decals applied at each race in a season! Mike

[JimClark]

yup I know mike he did the graphics for my 1/16th Bardahl.

Jim

[racer504]

Still wondering?

Have you determined a price for the 1/10 scale 8255 hull kit yet?

[cybercrxt]

RACER, Very sorry for the delay! The price for just the framing will be $135 shipped, and the price for framing, and sheeting is $225 shipped, as long as you are in the continental USA. Mike, madaccord@hotmail.com

[cybercrxt]

Got the Medium Blue painted last night, and added more SG100 intercoat clear, so its ready for another 600 grit sanding, and the light blue next, then the dark blue. Enjoy, Mike

[TotalPackage]

mike your pm box is full

[TotalPackage]

pm box is full

[cybercrxt]

Cleared out....

Ok, so I worked late last night on the build. Got the paintwork done. All I have to do now, is decide if I want to paint the cockpit black, or use black vinyl. Not sure how I feel about black vinyl and its long term ability to stay glued on well. Anyways, I will be scuffing the hull again tonight, adding the decals, and doing the clearcoat. Then in a few days, I will sand the clear flat, knocking down the lines created by the vinyl graphics, then reclearing again. Enjoy, Mike

[ace028]

That looks awesome man!!!!

[cybercrxt]

I have been working on 1/8th scale hydroplane framing plans over the last month or so, correcting all the errors in the plans, correcting the cross member to keelson and engine well fitment problems that I am finding exist in every set of Newton plans I have worked on. Its amazing just how off a lot of the plans are! This enables me to get the new CAD framing drawings laser cut and I am able to offer these kits to you. You will be getting all the framing parts that are shown in the Newton plans. I have a good amount of plans already done and ready for cutting, and many many more plans that I can offer very soon. If you have any interest in a kit, just send me a PM or email to madaccord@hotmail.com and I will give you a quote. Below is a list of the framing kits I have already done. Now, these “base” framing kits can make a variety of boats, so if you see a master hull roster # in the list below, check and see if it might work for your desired hull. I am going to list the exact sponsored hull my plans originated by, so you can use that as a starting point. I will also be offering sheeting kits for a few select hulls that I build for myself, so ask about that if its something you need. Thanks, Mike Luszcz, ML Boatworks (252) 717-6282


List update:
Finished Framing sets:

1) 105-A, 5560P, ‘55 Thriftway 1/8th scale, 1/10th scale, 1/16th scale
2) 101-A, 6740, ‘67 Bardahl- Makes may “Karelson Hull‘s” 1/8th scale
3) 124-A, 7495, ‘74 U95 Turbine 1/8th scale
4) 135-A, 8025, ‘80-82 Turbine Pay N Pak 1/8th scale
5) 138-B, 8255, ‘82 Executone and MANY others 1/8th scale, 1/10th scale
5) 8255 GAS KIT IS NOW READY Framing kit is $190 Shipped (CONUSA), Framing & full sheeting kit is $310 shipped (CONUSA)
6) 146-F, 8700, ‘88 Miller High Life/ Circus- Offset cowling 1/8th scale
7) 146-F, 8700, ‘88 Miller High Life/ Circus- Cowling adjusted to Center 1/8th scale
8 ) 149-B, 8701, ‘87-91 Miss Budweiser -1/8th Scale
9) 110-A, 6925, ‘69 Pride of Pay N Pak (Outrigger style hull)-1/8th scale
10) 176-F, 8806, ‘96 Dewalt and MANY others-1/8th scale
11) 137-A, 8200, ‘82 Atlas Van Lines (Weiblehaus Sponson Mod)-1/8th scale
12) 137-L, 8200, ‘90 Turbine Oberto (Weiblehaus Sponson Mod)-1/8th scale
13) 132-A, 8012, ‘79-80 Miss Budweiser Humpback w/ custom hatch framing- 1/8th scale
14) 132-A, 8012, '79-80 Miss Budweiser Humpback modified w/ centered engine well-1/8th scale
15) 158-D, 8700, ‘94 Smokin Joes, 89-90 Circus
16) 111-A, 6403, ‘64 Tahoo Miss

Working on Now (All 1/8th Scale for now):

1) 140-A, 5762, ‘60 Thriftway Too
2) 106-N, 6207, ‘75 Oberto and MANY others
3) 147-A, 8501, '85 Bubble Budweiser
4) 172-A, 9601, ‘01 Miss Bud T3 T5 T6
5) 135-E, 8410, ‘86 Seven Eleven

Plans I have, and will be drawing soon:

1)157, Winston Eagle Lobster
2) 121-L, 6615, ‘66-68 My Gypsy
3) 162-B, 9210.5, ‘93 Circus Twin Wing and others
4) 164-A, 9401, ‘94 Miss Bud T4 (Will also be modifying to make the Peters and May U-37 hull)
5) 172-B, 203, ‘04 Vacationville.com, Master Tire

[cybercrxt]

Thanks guys. OK, got home, got the cockpit area painted black, applied decals, and added the clear. I am pretty happy right now! Now I have to decide if I want to sand and reclear to knock down any decals lines...Hard Decision, but for now.....Everyone, meet your 1982 Executone Telephones, the 1/8th scale version!