I would like to try a 7XL with a small prop and see what happens
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
I've got a Fieago 7XL, 2370KV with Etti 150 and Grim 57/3 in the UL1 and it runs like a charm. But IMO, the Nue 1515Y with Woltz .078" wire drive, M440 and the CC240 is the way to go. We run consistant 48-50mph (data logged) on two other stock UL1's and the two setups above pass them like they are standing still! Just have to make some lead adapters this winter for the EagleTree ( deans ultra to 5.5 bullet) and see if I can fry an Eagle Tree on a Nue1515
a 7XL with a 57mm prop?
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
5 or 6s is too much voltage for a 7xl
Off subject, but.....I once got a set of 300A CT's shipped to me instead of some guy who ordered them from Norway...Called EagleTree and got them off to the guy..but I then started wondering that when you exceed the ELoggers amp range (I think its 100A) if you couldn't buy these CT expanders for the hotter setups instead of frying the logger. Plus, I think it stinks that they have the deans connector built in to them, limiting the current..I made some 5.5 to deans adapter jumpers, but still feel that I'm probabbly gonna cook something..That's why I'm afraid to use them in the Nue/Fieago...thats alright, the only thing we have up here in new england is block ice and snow...
Would a turnigy 180a esc fit into the hull of a ul-1?
http://www.hobbycity.com/hobbyking/s...hless_Boat_ESC
I fit that esc into a vacu-pickle, but it was a tight fit. It is probably too tall for the ul-1.
Good to know, this will probalby be a new motor/esc combo for my ul-1. I just read about the new venom boats 2 seconds ago so new ul-1 power is going to have to wait. I just got a grim 40x57/3 and strut depth is set to 1" so soon as weather breaks I can test it this setup then work on strut adjustment. Looking forward to it.
Oh man!
a 7XL in a UL-1, all I can say is yes it will mount up just fine
make sure you bring someone with a video cam, cuz we all want to see this one run..
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
Thanks and does it come with new bolts or use the old ones? Their are a few other things I need to do to the ul and also gotta wait for weather to clear and it will be ready to go. I am currently hitting high 40s (46-47) close to 50 but can't get over the hump. I honestly think the boat will do over 50 with my setup, but I don't have the best gps (kinda big) and I think it is weighing me down due to the size of it. I am running 1" strut depth and a sharpened and balanced (by egneg) grim 40x57/3.
the motor does not come with new bolts, you should be able to use the stock ones..
what batteries are you using?
are they at least 30c?
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
I will be using 2 2s Zippy 4500mah 30c and 2 2s zippy 5000mah 30c heres the esc i ordered http://www.hobbycity.com/hobbycity/s...ter_Cooled_ESC
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
Yes i have, when I ordered the boat the 4500 30c where the first batteries I got with it which have several runs on them. The 5000 30c I just got and they only have 2 runs on them and work wonderfully temps where good on both sets of batteries. I just switched the stock esc to 5.5mm bullets.
On this new motor/esc combo I am going to use are the 5.5mm bullets i mentioned above over kill for the 3 wires for esc to motor connection or ok?
no such thing as over kill, trying to get more amps to our motors
I'm thinking of changing mine to 4mm on the motor
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
GREAT, every connection on the new setup will be 5.5 then. sweeeeeet, I can't wait to get this thing in action. After I get everything installed in the ul I am going to take the stock ul esc/motor and put it in my SV...
How do you feel about the esc I ordered? Do you think it will be up to the task?!?
That esc should do just fine, just watch your temps on the first run
.NAMBA20...Caterpillar UL-1, P-Spec OM29, P-Mono DF33, P-Spec JAE, Aussie 33" Hydro-LSH, Sprintcat CC2028 on 8s, PT SS45 Q Hydro, PS295 UL-1 power, OSE Brothers Outlaw QMono 4-sale, Rio 51z CC2028 on 8s
Grimracer did you delete the picture of the new cat? I can't find it.
Here you go...
https://forums.offshoreelectrics.com/...ad.php?t=10827
Is there a direct link. The above link goes to another long thread which goes to another... etc.
Thanks
I guess I don't see the problem... They guy asked for the picture and that is what I gave him.... I can only assume you want this link instead?
https://forums.offshoreelectrics.com/...2&d=1255540288
Bookmarks