Motor Mounts

**Punisher 67** · 10-04-2009, 11:07 PM

Hey guys , by popular requests I am going to advertise my mounts here , Steven also thought it a good idea . I will apologize if they are a little pricey but they do take a lot of time to make .

Some youtube video's of the build process , I have since gone to a .25 bit for the smalls bringing the build time to just over 2.5 hours for the basic mount less ESC plate

http://www.youtube.com/watch?v=vRscUpsFGgc

http://www.youtube.com/watch?v=oSDUaDG_Gfo

These are the small mounts they will accommodate Feigao's , Medusa's , Neu's from a 1512 to a 1527 . these will work with a 4" stringer and are 3/16 in thickness

SMALL MOUNTS

basic mount = $50.00
ESC plate = $7.50
Shipping = $7.50

**Punisher 67** · 10-05-2009, 11:04 AM

MEDIUM MOUNTS

These are designed around the Feigao 580's or any motor to 45mm in diameter , Also for Lehner 22xx . they come in a 4" and 5" stringer width . mounts are 3/16 in thickness . this now will include the castle 1717 motor

Basic mount 4" = $55.00
Basic mount 5" = $60.00
ESC plate = $7.50
Shipping = $7.50

**Punisher 67** · 10-05-2009, 11:15 AM

LARGE MOUNTS

These are for the larger 22XX Neu's and 30xx Lehners , these take a fair hike due to the fact they are 3/8 thick and take 6+ hours from start to finish , the large Leoperds come in 1/4 aluminum

Leoperd 5692 mount 1/4aluminum w/esc plate...$85.00 without esc plate...$75.00
(mounts below done in 3/8 aluminum)
Basic mount Neu 22XX + Lehner 3080...............$100.00
combo Motor / Schulze controles........................$125.00
With ESC Plate............................................. ......$125.00
Shipping.......................................... .....................$10.00

**Punisher 67** · 10-05-2009, 11:22 AM

FLAT BOTTOM CAT & RIGGER MOUNTS

These can be ordered with whatever bottom width you want , the ones in the picture are a 2" and 2.75" for the smalls and mediums. You will have to install a small wooden stringer system for these to mount . they dont show in the pictures but come with mount holes drilled in on the bottom sides or drilled through on the bottoms for mounting

Basic mount small= $30.00 36mm motors
Basic Medium = $40.00 39 - 41mm motors
Big Medium = $50.00 Feigao 580/Lehner 22xx.........44 - 45mm motors
Basic large = $75.00 Neu 2215 to 2230 motors 1/4 Aluminum
Big large = $100.00 for Lehner 3080 with Schulze 40/160 combo machined in 3/8 aluminum , Neu 2230 also available
Shipping = $7.50 small + medium
Shipping = $10.00 Large mounts
ESC Plate = $7.50 small + medium
ESC Plate = $10.00 leoperd 5692 or 2215 mounts
ESC Plate = $12.50 on large mounts Neu 2230 or Lehner 3080

**Punisher 67** · 10-05-2009, 11:30 AM

CUSTOM

I cannot give a price on these since it will depend on what you need and how long it takes to design and make , some previous requests below

1st picture was for Jesse J's outrageous dual motor Intruder

The 2nd and 3rd picture is a Racemechanix Engineering designed mount , I have to say it is one of the nicest mounts I have had the pleasure of machining . it will work with a Neu 2215 or 2230 motor just the frame connectors would need to be adjusted for length .
Price on the 1/4 alum units = $90.00 + shipping
Price on the 3/8 alum units is $115.00 + shipping

4th picture is also a Racemechanix Engineering design but for a 4" stringer and the Neu 15XX series motors and price is $65.00 + shipping

5th picture is a 2215 low mount 4.0" stringer

**tiqueman** · 10-05-2009, 07:06 PM

Extrememly good looking mounts Peter. Im not in need of any now, but will be looking to you in the future. Very nice.

Scott

**Fast One** · 10-06-2009, 08:36 AM

These mounts are top quality and very well designed and machined.
Pete is an excellent person to deal with and his custom work is first class.
I would have no hesitation in recommending his services to anyone.
Shane Deacon Australia

**RCprince** · 10-06-2009, 12:52 PM

Peter, your a master craftsman.

**Punisher 67** · 10-06-2009, 03:59 PM

Thank you very much all , I will do my best for our little community........

**Flying Scotsman** · 10-07-2009, 12:42 PM

Peter, as usual crapy workmanship, awful music choices and dreadful video presentation

How long did it take you to write the code for a mount?

Douggie

**wolf IV** · 10-09-2009, 01:07 AM

Originally Posted by Peter Zicha

FLAT BOTTOM CAT & RIGGER MOUNTS

These can be ordered with whatever bottom width you want , the ones in the picture are a 2" and 2.75" . You will have to instal a small wooden stringer system for these to mount . they dont show in the pictures but come with mount holes drilled in on the bottom sides

Basic mount small= $35.00
Basic Medium = $45.00
Basic large = $55.00
Shipping = $7.50

can you make these with say a 10-15 deg angle on one end? im looking at fitting a 1527 in a mean machine and cant put rails in it due to the low profile cowl

this would be perfect if the back of the mount was higher for a downward angle for the shaft to flex union.

**Punisher 67** · 10-09-2009, 03:43 AM

If you give me what hight you want the front and what hight you want the rear I can work out the exact angle you will need............

Originally Posted by Flying Scotsman

Peter, as usual crapy workmanship, awful music choices and dreadful video presentation

How long did it take you to write the code for a mount?

Douggie

It depends on the mount Douggie , the larges can be up to 3000+ lines of code , designing a new mount can be very time consuming

**blakybob** · 10-09-2009, 01:11 PM

These mounts look awesome Peter!!! If the ones I have now need replacing I'll DEFINITELY be buying some of these from you.

Blake

**wolf IV** · 10-10-2009, 02:28 AM

thankyou so much for responding so quickly! i built one out of some stuff i had laying around, not as pretty as yours but i will get some from you in the near future foresure!!!

**Punisher 67** · 10-10-2009, 01:57 PM

Looks good Josh , whatever works my friend

**Jesse J** · 10-13-2009, 12:25 PM

The beauty of Peter's mounts is that they are also versatile. The mounts for the intruder were designed for 1515 cans, but since I had to sell them to buy beer, I have been using Proboat motors and the mounts still work!! these motors are shorter, but the mounts had holes in the right places and they hooked up nice. Can't wait till I get a real job and buy me a pair of NEW NEUs for the "Duchess".

Great work Peter and you don't charge enough $$ for your time and diligence!!

**toysRme** · 10-13-2009, 08:41 PM

Hi Peter,
i would like a mount for a mean machine aswell, to suit a 1518 NEU.I tried the mount you made me last month for the 1518 but its better suited to a mono.
Your flat bottom mount with alloy angle bolted to the sides so you glue two hard wood bearers to the hull,so you can screw into from the top would work nice(easy access to the mounting screws)
Many thanks for the two mounts you sent me last month

Craig B

**toysRme** · 10-14-2009, 04:38 AM

Hi Peter,
this is what i had in mind for the mean machine.Angle on both sides of the mount.

**Punisher 67** · 10-14-2009, 11:09 AM

Craig......I can make an addition to the mount G-code and have the side mount arms machined as part of the mount , would you like that better

**toysRme** · 10-14-2009, 06:20 PM

Peter,
If you use the alloy angle on the side you wont have to use the 4/5mm rods to align/join the two motor plates, if you use two screws per plate(front and rear) per side(8 in total) it will make it a lot stiffer.Just my thoughts but i see your design will also work,just worried about surface area for thrust load? And the angle will hide the wood mounting blocks glued to the hull

**bonewar** · 10-21-2009, 08:55 PM

Peter , I just received the motor mount for the 1521. It is awesome , and is going to look real nice inside the hull . Thank you very much. Rick

**Punisher 67** · 10-22-2009, 11:03 AM

Good to hear Rick , happy building

Craig your mount as requested

**toysRme** · 10-22-2009, 07:38 PM

Thankyou Peter,
this is just what the mean machine needed to finish it off.
Heres the 4" mouint you made for my brothers DF29, nice piece of work Peter

**Punisher 67** · 10-23-2009, 02:44 PM

Thank you for posting some pics , looks awesome..................

**Tuslow1** · 10-25-2009, 11:57 PM

PZ, your mounts are simply put "Beautiful", and I look foward to doing biz with you soon!!!

**toysRme** · 12-10-2009, 06:05 AM

Hello Peter,
Have been very busy so i havent finished the MM yet but heres the mount you made for me,
Ill send you the finished pics soon.
Many thanks
Craig

**Punisher 67** · 12-10-2009, 10:51 AM

Originally Posted by Tuslow1

PZ, your mounts are simply put "Beautiful", and I look foward to doing biz with you soon!!!

Thanks for the kind words Ken , just give me a dingle and we will have you set to go

Originally Posted by toysRme

Hello Peter,
Have been very busy so i havent finished the MM yet but heres the mount you made for me,
Ill send you the finished pics soon.
Many thanks
Craig

Thant looks awesome Craig , thanks for posting

**mappo** · 03-06-2010, 08:57 PM

Hey Peter,
I got the 1521 motor mounts today. what a beautiful piece of work, exquisite job! thanks..

**Punisher 67** · 03-06-2010, 09:05 PM

Happy you like it and thank you.....Only the best for you guys

Can you do me a favor , these are the new type 1521 esc plates a smidgen longer than my old ones , can you post a picture with it craddling the motor . I make a servo plate for 4.0" and 5.0" stringers now

$22.50 shipped for the 4.0inch
$25.00 shipped for the 5.0inch

thank you

**RaceMechaniX** · 03-09-2010, 07:36 PM

Very cool idea Peter for the rudder servo mount.
Here are some pics of your 2215 mount. Works perfectly!

Tyler

Thread: Motor Mounts

Thread Tools

Display

Motor Mounts

hydro / tunnel mount

Hydro / tunnel mount

engine mount

Bookmarks

Bookmarks

Posting Permissions