Keda MOTOR Clearence Sale

[JackBlack26]

Chud, that motor should move the Spartan pretty well and allow you to possibly run a bigger prop than you normally would due to the higher amount of torque being produced on 6S, considering the low amp draw required to generate that power. A T-180 should allow you to run a x445 or X447 with that motor to get that boat screaming!! I see guys on the Traxxas forum saying they are running a 2200 Castle motor on 6S in this boat but why risk it to go real fast for a short amount of time, with a small prop, when you can get a motor to go just as fast, with a large prop, for at leas 5-7 minutes of run time. More if you go 2P.

And Ray is right. If I remember electrical theory correctly, Y motors generate more RPM and Delta motors generate more torque.

[CHUD]

Chud, that motor should move the Spartan pretty well and allow you to possibly run a bigger prop than you normally would due to the higher amount of torque being produced on 6S, considering the low amp draw required to generate that power. A T-180 should allow you to run a x445 or X447 with that motor to get that boat screaming!! I see guys on the Traxxas forum saying they are running a 2200 Castle motor on 6S in this boat but why risk it to go real fast for a short amount of time, with a small prop, when you can get a motor to go just as fast, with a large prop, for at leas 5-7 minutes of run time. More if you go 2P.

And Ray is right. If I remember electrical theory correctly, Y motors generate more RPM and Delta motors generate more torque.

I'm sold going to place my order for it this friday it will sure help me out to save alittle more money for the next esc,Thanks BUD'S

[Brushless55]

The 3D would be a bad ass motor for a Revo!!

[midnightsabotage]

Would the 2364kv motor on 4s be too much? 34k rpm at 14.4v. Higher than that on a charged pack, of course.

Thinking 3s might want to pull more than the recommended max of 114amps on a decent prop but would run a bit below 30k rpm.

The 2000kv ones are sold out unfortunately. Figure a little propping down and this 2364kv could still be a decent set up? or no?
I believe grimracer recommends the AQ ammo 2300kv motor as a good upgrade for the SV27 on 4s? This seems quite similar to that thinking.
I do like overkill...

Please point me in the right direction here! I'd like to stick with 4s if possible. Or 8s, but I don't have the HV escs yet.
And i'd probably have more use for one of these motors in multiple/future applications if I stuck with one in the 1800-2400kv range.

Thanks!
-Jeff

[Brushless55]

Would the 2364kv motor on 4s be too much? 34k rpm at 14.4v. Higher than that on a charged pack, of course.

Thinking 3s might want to pull more than the recommended max of 114amps on a decent prop but would run a bit below 30k rpm.

The 2000kv ones are sold out unfortunately. Figure a little propping down and this 2364kv could still be a decent set up? or no?
I believe grimracer recommends the AQ ammo 2300kv motor as a good upgrade for the SV27 on 4s? This seems quite similar to that thinking.
I do like overkill...

Please point me in the right direction here! I'd like to stick with 4s if possible. Or 8s, but I don't have the HV escs yet.
And i'd probably have more use for one of these motors in multiple/future applications if I stuck with one in the 1800-2400kv range.

Thanks!
-Jeff

so that motor in a SV27?
yeah baby! over kill to the max, or maybe just perfect
it would be a fast motor for sure, only need about a 40mm prop and hang on!

[midnightsabotage]

well i'm looking for a good motor (or 2) for my 33" cat. or whatever hull I get next, I suppose. Not sure how soon i'll build that cat. I just want plenty of power on 4s for whatever I get. That's why i'm hoping it'll be flexible. But I recall the "grimracer recommended" sv27 upgrade being the 2300kv ammo motor, I think. I recall something about dropping to the 37mm prop though with that too.

But twin Keda 2364kv's on 40mm props might be way too much fun. The motors are 114amp max, so perhaps the turnigy 120 escs would be enough too. Might try to find some cheap t-180s though to be safe. I only worry it might be too much for the motors. I'm not experienced with setups enough to know yet. Hence me asking. Help! hehe
-Jeff

[Brushless55]

yeah that motor on 4s in a small cat like that would rock!
and twins, oh man!

[neal58cobra]

Will this be a straight bolt up to a miss geico? As in same mounting holes?

[midnightsabotage]

Will this be a straight bolt up to a miss geico? As in same mounting holes?

No idea on the mounting. It's a 40mm diameter motor, not a 36. So perhaps not. I'd want to upgrade the motor mount in the Miss Geico running a 40mm motor anyhow though.

The 2364kv Keda would be nuts in a Miss Geico... But you'd might need atleast a 120amp esc, perhaps even a 180 to be safe. Also, you might need to run a smaller prop. That's my guess. It's a pretty high kv motor for 4s. Also, no idea on runtimes with that setup - shorter though!

I think most would be happier with something in the 1800-2000kv range with a larger prop for pulling less amps and longer run times. Not sure how the speeds would differ, but I can't imagine they'd be worlds apart if both setups were propped correctly to run cool.

But as I said earlier, I'm not too experienced and these are just guesses from what knowledge I think I've overheard on here over the past few months. :p
I would have liked to see the 2000kv Keda still in stock.

My SV27 has a 1800kv 36mm motor with the stock 45amp AQ esc and runs a small 37mm 3-blade carbon prop and does pretty well. Don't want to prop that up until I upgrade the esc, for instance.

-Jeff

[Drax21]

Would the 2364kv motor on 4s be too much? 34k rpm at 14.4v. Higher than that on a charged pack, of course.

Thinking 3s might want to pull more than the recommended max of 114amps on a decent prop but would run a bit below 30k rpm.

The 2000kv ones are sold out unfortunately. Figure a little propping down and this 2364kv could still be a decent set up? or no?
I believe grimracer recommends the AQ ammo 2300kv motor as a good upgrade for the SV27 on 4s? This seems quite similar to that thinking.
I do like overkill...

Please point me in the right direction here! I'd like to stick with 4s if possible. Or 8s, but I don't have the HV escs yet.
And i'd probably have more use for one of these motors in multiple/future applications if I stuck with one in the 1800-2400kv range.

Thanks!
-Jeff

I have this motor in my Pursuit with a X642. The motor does produce a lot of amps but with silver solder I have seen no problems. Torque is unbelievable at such a high KV. I'm thinking a X442 would work perfectly.

[Brushless55]

Will this be a straight bolt up to a miss geico? As in same mounting holes?

It will bolt right in and hang on!!

My SV27 has a 1800kv 36mm motor with the stock 45amp AQ esc and runs a small 37mm 3-blade carbon prop and does pretty well. Don't want to prop that up until I upgrade the esc, for instance.

-Jeff

the stock SV27 esc can take alot bro!
I run a 48mm prop with no issues at all...

[Steven Vaccaro]

Most of the 2374kv motors are gone at this point. I have a couple left with esc's as combos. I have to double check the stock at this point.

Whats left is a bunch of 3513kv 3s motors, 1828kv 4s motors and 1391kv 6s motors.

[Drax21]

Wow these have sold fast. I guess I am gonna see a lot more vids of people running KEDA motors in their boats. At the moment I say "Its a KEDA motor" to other boaters and they say "so a cheap one, never heard of it" then I show them a video and they are like " where can I buy one?" I think KEDA still have a lot to offer, just need promoting more. Will you be getting any more in Steve or is this clearance for good?

[midnightsabotage]

Dang, I think I sold them all for you while I was inquiring. Didn't even have a chance to buy any.
Hope everyone posts videos once they get theirs running!

[CHUD]

Just payed for mine 4047 1391kv with watercooler,Sorry to say that I could not buy a sharpend and balance 442 , where out of stock crap!Looks like I'll have to use HJ to run my df33 ///O well can't win them all.///But Im really happy that the spartan now has a motorand from that vid she'a goin to run vary well,Thanks steven