Tweet
Hi Guys,
i hate to do this but i have a small family issue that has come up so i have to sell some toys.
1st up:
All Brand new Insane FE30 ARTR, boat has never touched the water.
The boat was built and set up by Tony ( properchopper ) there are several vids of his FE30 builds here on OSE.
here is the rundown
FE30 yellow/white hull
insane hardware kit, turn fin, FE30 motor mount
kintec racing servo mount
aeromarine welded .187 flex
Neu 1515 1Y motor, not a CC a true NEU motor
hrc cooling jacket
octura coupler
m545 B/S and back cut prop
T-180 Esc ,seaking, allready programmed, staright cooling inlets replaced with 90* banjo fittings
Neutronics 8mm bullets
Lg bore water fittings, inlet and outlet
Digital bb hi torque servo
Paid Tony for the build
JRS Stand
Monojeff windshield, paid for and on its way to me
Insane decals, NIP
2x Turngiy 4S 4000mah 40-50C lipos, NIP
all you need is your Tx/Rx and she's ready to go
Asking $ 800.00, i have $ 1085.00 in it as it sits *** SOLD Thanks Sean !! ***
Next up is a boat i bought a few months back from Dangerous_Toys
the boat is brand new,never seen water and is ARTR as well
here is the rundown on it
1 Off Custom Carbon Composite 28" Mono Hull, with Carbon/Kevlar lay up inside.
Kintec billet hardware, stinger drive, rudder w/water pickup ,rudder bracket, trim tabs
Kintec billet turn fins
ETTI motor mount, billet,carbon fiber
Tacon 4074 2150KV Motor
HRC Billet Cooling Jacket
Octura 5mm x .187 coupler
Hughey .187 Flex shaft
Octura Balanced, sharpened X640 Prop
Octura Prop Nut
Carbon Fiber Stuffing Tube Mount
Turnigy T-180, 180amp water cooled esc
EXI D226F steering servo
Carbon Fiber servo mount bracket
Turnigy 4S 5000mah 40-50C Lipo Pack
Flotation
Aeromarine Big Bore Water Outlets
Cooling Lines
Billet antenna mount
Custom Graphics and Paint
.
Here are the specs
28" long
10.5" wide
33" overall length with rudder
Asking $ 300.00
Thanks For Looking, More Pics Available By Email
Giz.
Deal Pending
i hate to do this but i have a small family issue that has come up so i have to sell some toys.
1st up:
All Brand new Insane FE30 ARTR, boat has never touched the water.
The boat was built and set up by Tony ( properchopper ) there are several vids of his FE30 builds here on OSE.
here is the rundown
FE30 yellow/white hull
insane hardware kit, turn fin, FE30 motor mount
kintec racing servo mount
aeromarine welded .187 flex
Neu 1515 1Y motor, not a CC a true NEU motor
hrc cooling jacket
octura coupler
m545 B/S and back cut prop
T-180 Esc ,seaking, allready programmed, staright cooling inlets replaced with 90* banjo fittings
Neutronics 8mm bullets
Lg bore water fittings, inlet and outlet
Digital bb hi torque servo
Paid Tony for the build
JRS Stand
Monojeff windshield, paid for and on its way to me
Insane decals, NIP
2x Turngiy 4S 4000mah 40-50C lipos, NIP
all you need is your Tx/Rx and she's ready to go
Asking $ 800.00, i have $ 1085.00 in it as it sits *** SOLD Thanks Sean !! ***
Next up is a boat i bought a few months back from Dangerous_Toys
the boat is brand new,never seen water and is ARTR as well
here is the rundown on it
1 Off Custom Carbon Composite 28" Mono Hull, with Carbon/Kevlar lay up inside.
Kintec billet hardware, stinger drive, rudder w/water pickup ,rudder bracket, trim tabs
Kintec billet turn fins
ETTI motor mount, billet,carbon fiber
Tacon 4074 2150KV Motor
HRC Billet Cooling Jacket
Octura 5mm x .187 coupler
Hughey .187 Flex shaft
Octura Balanced, sharpened X640 Prop
Octura Prop Nut
Carbon Fiber Stuffing Tube Mount
Turnigy T-180, 180amp water cooled esc
EXI D226F steering servo
Carbon Fiber servo mount bracket
Turnigy 4S 5000mah 40-50C Lipo Pack
Flotation
Aeromarine Big Bore Water Outlets
Cooling Lines
Billet antenna mount
Custom Graphics and Paint
.
Here are the specs
28" long
10.5" wide
33" overall length with rudder
Asking $ 300.00
Thanks For Looking, More Pics Available By Email
Giz.
Deal Pending
Comment