Zonda gets a face lift.

[twissted]

They are, and yes that will get done.

[gsbuickman]

Nice Zonda cat Twisted :-) . sorry I missed your thread till today :-) . Zonda Design's some sweet road race cars too. I have a feeling the Zonda may run real wet with 4 lipos in it, especially with 2 in the back. I haven't had any luck running cats with lipos too far back. They seem to prefer the cells up in front of the motor (s) with the prop running +, to get the now p just a bit.....

[twissted]

Nice Zonda cat Twisted :-) . sorry I missed your thread till today :-) . Zonda Design's some sweet road race cars too. I have a feeling the Zonda may run real wet with 4 lipos in it, especially with 2 in the back. I haven't had any luck running cats with lipos too far back. They seem to prefer the cells up in front of the motor (s) with the prop running +, to get the now p just a bit.....

check this out. 6s batts in the rear of the motors

http://www.youtube.com/watch?v=j0mC0O3s1kY

[nemz305]

nice build. love the color as well

[twissted]

Thx

[QUOTE=nemz305;538888]nice build. love the color as well]

I have added some new props to try as well. I will be adding some bigger esc's so that 8s is possible.
I my try the esc's I have now if I can figure out how to get past the shut down that happens when I try then on 8s.
large scale rc 006.JPGlarge scale rc 007.JPGlarge scale rc 008.JPGlarge scale rc 009.JPG

[borgie]

could you post the link for them props? thanks nick

[twissted]

25602.jpghttp://hobbyking.com/hobbyking/store...P1_4_3x3_.html 25601.jpg
You will need to use some drill bits and drill out the center to the size you need as they are 4mm. Work your way up and don't try to do it in one try or you could get of center.

[twissted]

39032.jpg
These will be going in as soon as they are available to me.
here are the specs.
Programmable Settings:
Reverse Type: Reverse lockout, forward only, forward / reverse*
Motor Direction: Normal*, reverse
Reverse Amount: 25%, 50%, *75%, 100%
Starting Power: Low, normal*, high
Voltage Cutoff: Lipo 3.0V per cell, NIMH 40% of power up voltage
Motor Timing: Low / normal / high*

*Default setting

Specs:
Motor Type: Brushless, sensorless motors only
Input Voltage: NIMH 15-33 cell, Lipo 6-12 cell
Operation Current: 200A Cont, 250A peak
BEC: No BEC, seperate BEC required
Thermal Protection: 95°C
Lost RX Protection: Delay 0.5 second
Dimensions: 115 x 50 x 31.5mm
Weight: 290g

[Tbauer]

Make sure you get the program box for them...... If your just going for speed your best props are the 3 blade 1.8 from Kintec. I hit 85 with 8s on the exact esc's you currently have. So if you can't hit 80, something ain't right

[Tbauer]

I also went to liner-less flex tubes, stainless steel and made my own oil/grease coupler with a fitting so I just pump it right in, no need to disassemble

[Southwest]

What size caps are on the esc, thanks? I see only 2 caps.

[Tbauer]

If your asking about the 200's then yes, there are only 2...... They say 63v 220uf

[twissted]

What Size?

Make sure you get the program box for them...... If your just going for speed your best props are the 3 blade 1.8 from Kintec. I hit 85 with 8s on the exact esc's you currently have. So if you can't hit 80, something ain't right

What size prop? 5018/3? 4518/3 I'll buy them if you could send a page to go to that would be great thanks.

[twissted]

I also went to liner-less flex tubes, stainless steel and made my own oil/grease coupler with a fitting so I just pump it right in, no need to disassemble

I like that IDEA! I'll give it a try.

[Tbauer]

I like that IDEA! I'll give it a try.

M850/3 Has a diameter of 50mm and pitch of 1.8 Fits 3/16 shaft. $32.00



M850/3-R Has a diameter of 50mm and pitch of 1.8 Fits 3/16 shaft. $32.00