PDA

View Full Version : leopard 3674 motor direction ?



johnmiffco
12-24-2014, 11:30 PM
1st hello
im new to this forum
2nd
I just purchased a really nice used revolt with only a couple hrs run time on it
and was all stock
well ,,,,not been set up yet
sp decided to upgrade and dial in all at 1 time
installed new leopard 3674 2200kv motor
seaking 180 esc
upgraded flrx shaft
thinned & sharpened turn skegs and rounded rudder
445,455,642 and stock props to dial in with

when I connected motor to esc by color code
blue,yellow,orange motor turns clockwise when set to "forward only"
in esc settings,,,,,
when set to for/rev it does switch at the receiver for and rev

? is,,,,,,,does the motor turn same rpm in both directions?
to leave it switchable at the receiver,,,,
or should I switch 2 wires to make it turn counter when set in forward only setting
would be nice to have a rev if need to idle backwards for some reason,

this forum is a wealth of knowledge on this hull
as why I got these components and did all the pre adjustments suggested
any advise will be heplful

tks
john

tlandauer
12-25-2014, 12:06 AM
Welcome to the Forum and Happy Holidays!


The color on the Leopard and the color on the Seaking are not necessarily color coded. You need to swap any two wires until the rotation is correct, DO NOT ALTER THE ROTATION BY SWITCHING THE RECEIVER'S CHANNEL 2 SWITCH. That switch should be in "N" position UNLESS it is a Futaba system or Tactic or Flysky.
I don't enable the reverse feature on my ESC, a full throttle blast IN THE WATER is not good for the cable because it is directional and repeated attempts will unravel the cable.

johnmiffco
12-25-2014, 02:05 PM
I do have a tactic receiver,,,,
but did swap wires around till is turning counter while switch is in N position
definitely wasn't going to make run in clock rotation under power
my buds and I are former formula tunnel drivers/racers
and now we are still chasing another around with the RCs now,,,lol
also as why im upgrading,,,more power,,,,
here is pic of the upgrades
125906
tks
have good holidays

tlandauer
12-25-2014, 02:47 PM
That is a fabulously upgraded Revolt with CF inlay! :thumbup1::rockon2:
I am under the impression that in order for the Tactic to work properly ( i.e. , throttle calibration) the channel 2 switch needs to be in the "R" position.
I am kind of surprised that you have it working on the "N" position. Might want to check that again...
Someone correct me if I am wrong.

johnmiffco
12-25-2014, 03:37 PM
tks ,,,,,
I built and raced the tunnel boats as in my avatar
so when got this 1
I gutted all hardware and layed carbon bottom,,,made carbon trays for 4s battery and esc as low as possible and in center
flipped it and trued the bottom flat,,,,and gave it a 400 grit finish as we did with larger hulls
then thinned and polished the running gear,rudder and turn fins

what I found with the tactic is,,,
ur correct on the switch on the reciever
in "forward only" mode,,,,no matter what direction I reverse the motor wiring
I have to set reciever to R position to get power when pull trigger,,,,,
when in N position it has no power when pull trigger
push trigger forward,,,,will power up
and if I set it "for/rev" mode
it will go forward when pull trigger and rev when push trigger forward set in N position
so that is the choices,,,,
forward only in R
for/rev in N
will be going out for a test run next week
to adjust tabs,fins,prop height and start with the m445 then x642 props
tks for help,,,,,,will probably switch to forward and r since now know that's correct,,,,

tlandauer
12-25-2014, 03:44 PM
I envy you with your racing experience and with the FORMULA Tunnel.
Have fun and Happy Holidays!

Sent from my D6708 using Tapatalk