NQD jet boat up grade need help

[Trexter67]

I am going to upgrade a nqd jet boat and I need a set up for under $50 exluding shipping I would like a motor between 3500-4000 kv. I need an ESC a motor and a battery and charger. Someone please help me out! I would like for it to be fast and powerful and mostly reliable.

[Alexgar]

What size boat and speed expectation also what batteries do you have might save ou a couple bux

[Alexgar]

Maybe 7l and 100 amp hobbyking esc

[TheShaughnessy]

check out rcuniverse.com under the fast electric boat forums. lots of set ups for this boat over there.

[Trexter67]

To Alexgar about an 18 in boat and I am new to hobbies like this why would I need such a large esc

[Trexter67]

To TheShaughnessy thank you for the website I will check it out

[C.B.R.]

I am going to upgrade a nqd jet boat and I need a set up for under $50 exluding shipping I would like a motor between 3500-4000 kv. I need an ESC a motor and a battery and charger. Someone please help me out! I would like for it to be fast and powerful and mostly reliable.I don't think you will be able to do it on $50 if you get new stuff.
I used this motor http://www.hobbypartz.com/07e-c-sl-12t-2040-blue.html
this ESC http://www.hobbypartz.com/07e-c-seaking-25a.html
and bought a couple 1300 mah lipos and it was $60 without buying a charger.
But these little jet boats are a blast to drive!
Here's mine
http://www.youtube.com/watch?v=Tt4GF-QkNmc

[C.B.R.]

Just noticed you are in TN, me too. Where at?

[Trexter67]

Memphis.I have been looking at hobby king and I found everything I need but the boat for $60. A 3800kv turnigy a 35a esc and a battery with charger. But thanks and cool video

[triumphjon]

what modification have you made to the intake please ? im running the same jet unit in a custom built cathedral hull 549745497554976currently with the stock motor until i can afford a brushless one !

[Trexter67]

I have not done anything yet. I have not even ordered any parts but if you want to see some videos on this jet out put just type NQD Jet Boat on YouTube. Sorry I could not help you any more than that

[C.B.R.]

I did no modifications to the intake or pump. Only put a piece of metal screen over the intake to keep from sucking in rocks in shallow water. I also drilled a hole in the pump for pressurized cooling for the motor and esc.

[triumphjon]

i shall need to put something over the intake as there is lots of blanket weed where i sail , which has already claimed my first prop ! where on the pump did you drill for a cooling inlet ?

[C.B.R.]

I put it here....

55000

in front of the nozzle so it doesn't block the nozzle movement.

[C.B.R.]

here are more pictures

55001

55002

55003

55004

[C.B.R.]

Trexter67, I am near Dickson,TN.

[triumphjon]

whats the plate below the nozzle for ?

[Trexter67]

How did you make the cover plate

[C.B.R.]

whats the plate below the nozzle for ?It could be called a ride plate, I made it to keep from hitting the nozzle on rocks when creek bashing. I never ran the boat without it, so I really don't know if it helped the performance.

[Trexter67]

How did you make it

[C.B.R.]

How did you make the cover plateNot sure what you mean by cover plate, unless you are talking about the ride plate. It is made from thick lexan. I used a sheet metal break to bend the lexan to match the shape of the hull. It is held on by the 4 pump screws. I'll get some pictures from the bottom tomorrow. Just got in from mowing the yard.

[Trexter67]

Ok I did that earlier as well, 5 acres

[sundog]

Memphis.I have been looking at hobby king and I found everything I need but the boat for $60. A 3800kv turnigy a 35a esc and a battery with charger. But thanks and cool video

Trexter, that 3800kv motor is not your best choice. Ideally, you want a 3000kv (3S) or 4500kv (2S) tops, or it will sound faster but go no faster. I just did a conversion for a member on RCU and tested it yesterday, it has the 4800KV HK motor. The last 10-20% of throttle just make more noise, not more speed.

A ride plate will keep the hull from porpoising at full throttle with an oversized motor. I have a larger 3000kv outrunner in mine and it required the plate to keep it on the water. Very fast out of the hole.

[Trexter67]

But will this motor work ok? It is an inrunner. I have already ordered the parts I want to know if I have messed up

[sundog]

Nope. I don't think you will be happy with it on either 2S or 3S. What battery are you going to be using?

[Trexter67]

1800mah 3s 20c

[Trexter67]

I have just found a turnigy 3000kv inrunner, 2623 is the size. Will that work?

[sundog]

If you have a water jacket for your motor you can use it with that battery - for a while anyway. Without a water jacket, it won't last long at all. Check battery temps often at first. You may experience the 'faster sound than speed' syndrome I spoke of before, or either it won't be able to attain top speed (not enough torque) and will heat up the battery significantly. If you decide on another motor, try to find something as close to 3000kv that you can. An outrunner that has a built-in fan will also do well in this boat. But that battery is borderline (36A). I usually recommend at least 2200mah and the highest 'C' rating you can afford. You really should read the Tear Into thread on RCU: http://www.rcuniverse.com/forum/m_7991409/tm.htm

[triumphjon]

hoping not to need trim tabs , but where did you source the mesh guard for the intake from ? im also looking into making my own metal prop !

[C.B.R.]

Ideally, you want a 3000kv (3S) or 4500kv (2S) tops, or it will sound faster but go no faster. I just did a conversion for a member on RCU and tested it yesterday, it has the 4800KV HK motor. The last 10-20% of throttle just make more noise, not more speed.
I haven't noticed that with mine, I have a 4800kv hobbywing (probably the same motor HobbyKing sells but from Hobbypartz.com). You can watch the video. That is how fast it goes on 2s, it is even faster on 3s. I have tried 4s, but would not recommend it to anyone!

[sundog]

Maybe because it sounds faster you just assume it's going faster. Is your transmitter trimmed to provide full throttle? You might check that. Then pay close attention to the speed (don't let the sound of the increasing motor speed influence you) and I believe you'll see boat speed stops increasing before motor speed. This has been noted several times on the RCU site with the 4800KV motor. It WILL burn up on 3S at WOT - it's just a matter of time. The motor is borderline on torque in this application. Jet drives require considerable more power than prop drives.

[TheShaughnessy]

i noticed what you are talking about (more noise but no more speed) with a 1800 kv motor on 4s with the 29 mm drive. Maxed out the efficiency of the drive, which i remember reading it being something like 21,000 rpm.

[sundog]

There should be a name for that. Maybe MES for maximum efficient speed, or SDR - speed of diminishing returns.

[C.B.R.]

Maybe because it sounds faster you just assume it's going faster. Is your transmitter trimmed to provide full throttle? You might check that. Then pay close attention to the speed (don't let the sound of the increasing motor speed influence you) and I believe you'll see boat speed stops increasing before motor speed. This has been noted several times on the RCU site with the 4800KV motor. It WILL burn up on 3S at WOT - it's just a matter of time. The motor is borderline on torque in this application. Jet drives require considerable more power than prop drives.Oh yea, I'm getting full throttle. I'm running a $40 boat with a DX3R! I noticed what you are saying with a 3s, it does reach the limit of the pump. With 2s this little motor is perfect. With a 4800kv on 2s you are only supposedly getting around 35,000 "no load" rpm. Works for me.

[C.B.R.]

Sundog, I watched this video of you boat, http://www.youtube.com/watch?v=8LiVQzF4EDQ&feature=related . It sounds like it is turning a lot more RPMs than mine does, but mine appears just as fast. I can see by watching when it reaches the pumps limit. I also don't have as much problem with cavitation as your boat was having. Maybe I just got a really good pump out of all this chinese junk. I never ran mine stock, took it apart as soon as I got it. One of the motor screws wasn't even in the motor, the rubber seal on the impeller shaft wasnt in the housing, and so much of the shaft was in the coupler the shaft was barely hanging in the rear bushing. Once i spent several hours putting things as they should be and making a new coupler because the stock one was out of balance and shook the boat like an earthquake, this is the most fun I have had in my 30 something years of R/Cing.

[sundog]

Ha! yes, that was my first Tear Into conversion. It had a 3200kv outrunner in it and lots of problems. I had eliminated the intake ramp and installed a grate over the (large) opening. It caused some cavitation as you could see. My newst incarnation has a larger air-cooled 3000KV outrunner on 3S 2200mah 30C and blasts out of the hole - similar to 'Big Bird's' 29mm conversion. I used a 28mm adapter plate (made for trucks) and Jeff Woldt custom connector. I agree, these are great fun and excell in rapids. During this last conversion I found it had a wobbly connector, and I went through 3 others in my parts drawer before I found a suitable one. Iv'e had one boat where the hole cut for the jetdrive was crooked! Didn't affect the running as far as I could tell, but another cry for quality control.

[C.B.R.]

Ok I did that earlier as well, 5 acresSorry, forgot about the picture.
55217

[pmdevlin]

there is a massive thread about upgrading these boats on rc universe, The ride plate (stator protector) is made from some mesh, cut from desk tidies (uk peeps go to staples or somewhere similar) the motors are very cheap, hobbyking or simiar. THe only problem is the drive impeller is very weak, and its very difficult to lubricate and make water tight, I used a syringe with light grease

I modified 3 of these boats to have fun with my two sons, but they just didnt get them! kept driving into each other and flipping them over. They are awsome fun on a shallow stream etc, but we have boating lakes near us, they are a bit boring on them, also, the motors get very hot and only really like short runs, well the ones I used anyway

[BILL OXIDEAN]

You guys need to quit teasing me with these jet boats, Imma' have to order me one if you keep it up : )

[triumphjon]

no teasing here , go on they are great fun !

[sundog]

I wanted to show these a while ago, but the computer they were on blew a power supply. Here is my latest incarnation. The 3000kv outrunner has a built in fan with no supplemental cooling but the esc is watercooled. Had to attach a ride plate to keep it from porpoising. These boats are a blast to build and run.

cxgDyYovldE

[C.B.R.]

Ran mine in some very shallow creeks this morning. It's hard to navigate rocks and make a video with a phone at the same time!

http://www.youtube.com/watch?v=lKF2SpAo28w

[faqcya]

C.B.R I tried that motor in my NQD on 3s and burnt it up in under 2 minutes. And I had good water cooling going through it.

[wparsons]

Oh yea, I'm getting full throttle. I'm running a $40 boat with a DX3R! I noticed what you are saying with a 3s, it does reach the limit of the pump. With 2s this little motor is perfect. With a 4800kv on 2s you are only supposedly getting around 35,000 "no load" rpm. Works for me.

The stock drive loses efficiency quickly above 25k rpm, anything more than that just makes more noise. A 4800kv motor on a fresh 2s pack is about 40k unloaded RPM, WELL above the efficiency of the pump.

I'm running a 3200kv motor on 3s in mine, and above 3/4 throttle just makes more noise and heat. I would go with about 3500kv on 2s if I were to build another one, that gives about 30k rpm unloaded. Less heat, and plenty of power/speed for rapids/creeks.

I can barely get above 1/2 throttle on mine in rapid sections without it getting too light and losing prime.

For anyone building one with an outrunner, hobbyking is now carrying water cooled outrunners and also a cooling plate with 19mm bolt spacing (it's like $5 for the plate, good deal).

[C.B.R.]

...

[wparsons]

...

Nice edit... too bad my email notification had the original.

Read the thread RCU, there's lots of discussion about the efficiency of the drive and what rpm range to stay in.

Most jet drives, even the very nice KMB ones, are happiest in the low 20k rpm range. Their 28mm drive says to stay around 21k.

I'm not saying higher rpm won't work or will ruin the drive, but you aren't getting any gains out of it by revving it faster like you would with a surface driven prop.

Mine is absolutely no faster from 3/4 to WOT but it definitely makes more noise and revs higher.

[C.B.R.]

Since you quoted me in your post, I assumed you were talking to me. I have read the ENTIRE thread on RCU. I don't agree with all of it, it is a collection of other peoples opinions. I chose to build my boat the way I wanted to, not to be a sheep and do it they way everyone else said to do it. I have 2 videos in this thread of my boat running, I don't see a problem with it.
But I did not do everything I was supposed to do according to the trolls on the RCU thread. I have a 5000mah 40c 2s lipo (was told it was too heavy), a 25a ESC (was told it wasn't enough amperage), and a 4800kv 4020 motor (was told it was too many RPM's).
But it seemed to work anyway.
http://www.youtube.com/watch?v=Tt4GF-QkNmc

[sundog]

Trolls? People offer advise and you refer to them as trolls? You won't get much help from here with that attitude, bud. They said 5000mah would slow that boat down (versus a 2000mah) because of the weight, not that it wouldn't work or fit. You were probably told the 4800kv wouldn't last on 3S, not 2S (preferred with that motor). And that 25A esc won't last long from my experience - you have been lucky so far. But your luck is running out here.

[C.B.R.]

Like I said, I havent ASKED for any help. I am always given answers even though I don't ask for them. Just like your entire post just now. That is all "your experience".
I done with this, going to drive my boat that doesn't work and leave the technical stuff to you experts.

[wparsons]

Since you quoted me in your post, I assumed you were talking to me. I have read the ENTIRE thread on RCU. I don't agree with all of it, it is a collection of other peoples opinions. I chose to build my boat the way I wanted to, not to be a sheep and do it they way everyone else said to do it. I have 2 videos in this thread of my boat running, I don't see a problem with it.
But I did not do everything I was supposed to do according to the trolls on the RCU thread. I have a 5000mah 40c 2s lipo (was told it was too heavy), a 25a ESC (was told it wasn't enough amperage), and a 4800kv 4020 motor (was told it was too many RPM's).
But it seemed to work anyway.
http://www.youtube.com/watch?v=Tt4GF-QkNmc

Like I've already said multiple times, I'm not claiming your boat won't work. What I am saying is that more rpm won't make these boats any faster, you can't argue with facts. I've seen my own boat first hand and other videos where they don't pick up any speed, just more noise, with more rpm. If I had a 2s 2200mah pack I would make a video of back to back runs with mine, and I bet the 3s pack isn't really any faster than the 2s pack. 2s on my motor is still ~27k rpm unloaded, which is more than the drive is happy with. I know for a fact it would run much cooler as well on 2s, and probably get more run time. If I were to build another, I would either run 2s or go with a lower kv motor to keep heat down and reliability up.

Your motor on 2s is the same (exactly the same oddly enough!) rpm as mine on 3s so I would bet that you don't really gain any speed (just more RPM and noise) between about 3/4 throttle and full.

Here's mine on a 3s 2200mah pack, the slow cruising parts are about 1/2 throttle and the WOT blasts are pretty obvious:

http://www.youtube.com/watch?v=lpTvhV-zU_E

[sundog]

Like I said, I havent ASKED for any help. I am always given answers even though I don't ask for them. Just like your entire post just now. That is all "your experience".
I done with this, going to drive my boat that doesn't work and leave the technical stuff to you experts.

LOL, the idea is that we can share and benefit from others' experiences so that you don' t make the same (sometimes costly) mistakes. But I understand your need to learn for your self. No worries, Sdg.

[NQD1]

What did you use for the water pickup?

[NQD1]

What did you use for the water pick up? Did you just use a peice if metal tube or did you order a special peice?

[wparsons]

I just used a short length of brass tubing (1/8" I think), cut at about a 45 degree angle on the end inside the pump outlet, and epoxied it into place.

[NQD1]

Ok thanks how far does it stick down into the jet?

[wparsons]

Ideally as little as possible, but it needs to be in a fair amount to function.

http://vnc.thewpp.ca/photos/TearInto/PICT0198.JPG

http://vnc.thewpp.ca/photos/TearInto/PICT0199.JPG

[NQD1]

Thanks! You guys are great quick response and lots of help!