Ammo and Turnigy!!!

[xxxrems38xxx]

hi boaters!!

Notice to everyone, the marine Turnigy 180A esc is not compatible with the motor 2300kv ammo there is a cogging effect and a sizzling engine at low rate! If someone has had the same config with the same problems it'll be nice to give me advice! thanks to all :o

[LiPo Power]

What boat is it in?
Is it Formula fastech? If yes, did you try your ESC with the stock motor?
Robert

[xxxrems38xxx]

yes with the stock motor all is alright nice accelerations timing at 11.25° and the esc and motor is barely warm

[LiPo Power]

Stock motor is one of the best motors out there for your boat. It has power and you can even up-prop your boat a little. Make sure to check temps as you do.
Are you running stock prop or X642? This upgrade prop is all you need to get more speed and fresh set of LiPos....
Robert





yes with the stock motor all is alright nice accelerations timing at 11.25° and the esc and motor is barely warm

[ED66677]

anybody has ever tried this combo?

[j.m.]

The ammo is a 6 pole, is the pro boat a 4 pole?

I know somebody posted a timing guide according to the number of poles a motor has...

Jon

[xxxrems38xxx]

Turnigy marine 180A is it compatible with 6 poles motors?

[j.m.]

http://forums.offshoreelectrics.com/showthread.php?t=15348&highlight=ESC+timing

[6S HYDRO]

the ammo 2300 is not a 6pole motor it is a 2 pole. the ul-1 motor is the 6pole one.

[6S HYDRO]

ul-1 esc runs this motor flawlessly and in the post above it states that it runs 10d timing. try the turnigy on 10 degrees

[xxxrems38xxx]

the timing of my turnigy is 11.25 ° and then moved to 15 ° and I have already try all the settings and nothing to do! which is strange because with my original motor and another motor in hobbyking everything works without worries! Do you think it would come from the radio or receiver?

[6S HYDRO]

maybe you got a bad motor, or the turnigy just doesnt like 2 pole motors

[6S HYDRO]

have you tryed the motor on the stock esc? they run great on sv-27 or ul-1 esc's

[xxxrems38xxx]

I'm going to buy a 60A aquacraft be sure that it works? is there a programming card for this esc? and up to how many lipo cells can support?

[BakedMopar]

which is strange because with my original motor and another motor in hobbyking everything works without worries!

If the speed control operates other motors then you should be looking at the motor for problems. Could be a bad solder joint or just a lemon from the factory.

[Brushless01]

The ul1 esc is great with the ammo 2300 !! No it comes pre programmed and ready to rock

[6S HYDRO]

yep just plug and play

[xxxrems38xxx]

can it operate in 5s?

[6S HYDRO]

yes but only for A short burst, like a speed run

[Brushless01]

On 4s with the Ammo motor and ul1 esc its more than enough run 4s it will last longer and be plenty fast enough .

[xxxrems38xxx]

Thank you all for your help!! My problem is solved, I bought a radio spektrum with a receiver DX3E RM 3000 and the cogging disappeared with some small adjustments that it's on the radio! It must have come from my radio "PROBOAT"!I have set the timing on 3.75 ° because your advice said that for the 2 pole motor timing was between 0 and 5 degrees and everything works fine now! Thank you very much

[forescott]

Ah, good ol proboat am radio!