- Ideas on Building a Reliable BL System by ReddyWatts.
- Number cells/Motor Kv/Prop Size/Hull Size
- Good Motor ESC & Servo Information
- OPC Lower Units and FE Conversion Kit
- esc cooler-no solderig
- Easy water outlet
- Money saving choices
- Cooling brain fart
- Stuffing Tube Sling Guard
- Lipo battery FAQ's
- Vacuum forming setups and information
- vacuum forming
- Cooling more than the windings
- What is hot and rocking at BBY
- Castle 5.5 Tip
- Connector Tip (Castle 5.5)
- Great stuff Foam For Hull
- Carbon Fiber, please tell me your tips and tricks!
- I need your help for outrigger boat
- The Full FeCalc install program file
- Screws and Nuts
- Seal that stuffing tube with a Vacum plug !!
- Pre-Cool your electrics before runs.
- don't under estimate fotation... in the cowl!
- Best water pick-up ever!
- tip. good work surface
- Stuffing tube seal on the outside.
- soldering- jig
- Installing a Wrap
- water resistant air scoop idea
- how to stain your pvc stands different colors
- Formula For Calculating Speed (Revisited)
- 5.5 Bullet parallel conectors
- Tactic radio mod/ no more pistix
- Flex cable greasing
- modded kos
- Simple Rear Hatch locks
- PWM rate
- t180 motor wire shortening
- Diamond in the Ruff
- Painted my HotShot tunnel
- Modifiying the EKOS
- My dilema!!
- Sealing the stuffing tube - this works great
- carbon fiber
- adj canard
- Servo Slow Down Module for my Tunnel
- Blueprinting UL-1 Motor Wires
- Waterproof pushrod seal.
- Interesting Sponson Mod
- Boat Hull reinforcement
- Welding cut end of flex cable.
- Motor might be just a little too big!
- Sealing Air Scoops on the Mean Machine
- Found a yellow paint match for Mean Machine
- Plastic mixing cups from mcdonalds
- Need to Shorten Motor Shaft
- Very cool decals for our boats
- water cooling
- Water outlet antenna tube holder
- New Water Pickup Prototype
- Fractional - Decomal - Metric Chart
- Bulletproof "Quick-Change" 4" rail motor mount
- twist on something I saw on RC groups
- How to get the cooling hose onto a hard to reach bulkhead nipple
- Really Kool "Dead Center" hardware mounting hole locator
- Easy way to strengthen the hull of the vanquish
- Spektrum temp sensors work with an Eagletree
- Tampons!
- subforums
- Liquid Electrical Tape!
- cooling jacket
- gell coat chips hull damage?
- Eagletree 150 amp to 300 amps in 15 minutes
- hands free vide recording with smartphone
- Rudder Tips
- D and Wye wind motors selecting a good setup for your model
- Parts Storage
- Conformal Coating Warning
- water in hull
- How does everyone store their boats at home?
- Tricks for painting in cold weather?
- iHandy App for strut adjustment
- Rare Earth Mag's
- proboat 2900kv motor
- 80mph race trim jae21fe
- Miss Geico 17 "brushed to INSANE 50MPH BRUSHLESS BOAT"
- Need help!! New paint job for my hull
- how do you guys carry your boat ?
- Modifying Swivel Brass water cooling fittings for better flow
- Turnigy 180a ESC
- saddle up!
- Stuffing tube cleaners
- How To: Remove Anodizing From Aluminum Parts
- Heres the best way to waterproof your electronics
- Radio box tape.
- GPS in CF hull mounting tips
- 300a ESC's that fit
- Heat Shrink Sizing
- How do you reinforce hull?
- Blueprinting Tutorial
- how do i make a windshield decal?
- painting question
- Miss Geico green paint
- Checking cooling system
- finding the center of the transom
- HiFei v4.11 Software Install
- quick and easy flooded stuffing tube
- Epoxy or CA glue
- A nifty $15 cooling system tester
- Hatch repair
- How to "freeze" the Epoxy cure process...
- Darin's Method for Making Paralelling Adapters
- A way to hold those rods, tubes, shafts & flexes etc.
- Best Battery Strap/Mount
- I apologize if this is not the place for a suggestion.
- Painting a windshield
- Here's something to save you time cutting carbon or fiberglass
- Mystic logo in vector
- What is this on the boat ?
- Gun Vise
- https://www.ebay.com/itm/42mm-Long-Waterproof-Push-Rod-Seal-Bellow-with-Aluminum-Fitt
- Electronics cooler and flusher
- Wild Thing
- Recommendation