Who's Running a Micro? => Less than 16"

[Meniscus]

Who's running a Micro => Less than 16"

Tell us what you have, what setup works best including props used, and what speeds your able to achieve! Also describe how it handles in various water conditions.

[ride1226]

Im quite curious as well. I really like the minis made my Minicatracing just unsure of getting something so small. Debating either one of those or trying to find a used vac-u-pickle or DF hydro.

[bustitup]

I'm getting ready to buy this set up

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300266886047&sspagename=STRK%3AMEWAX%3AIT&viewitem=&salenotsupported

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300256641799&sspagename=STRK%3AMEWAX%3AIT&viewitem=&salenotsupported

[Diegoboy]

Please LMK if that strut has any Vert adj

[Meniscus]

I'm getting ready to buy this set up

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=300266886047&sspagename=STRK%3AMEWAX%3AIT&viewitem=&salenotsupported

http://cgi.ebay.com/ws/eBayISAPI.dll...lenotsupported

I've been looking at that for quite some time. Can't wait to see what you can do with it!

[ride1226]

That looks to be a pretty nice little setup. And im sure with this boat being so small you really save alot on electronics as well. What do you plan to use for a motor mount and whats your power plant gonna be? So far Im thinking of following your footsteps.

[JimClark]

I have one of the struts I would have to measure it but there is not a lot of adjustment available. It is like .187 to .25 max

Please LMK if that strut has any Vert adj

[Meniscus]

After recent testing at the pond in some of the smaller stuff, I recommend trying a 380L Yes it's overkill, but on my Oberto and with Diego's Warrior, it's ridiculous! And lots of fun too!

[bustitup]

I have one of the struts I would have to measure it but there is not a lot of adjustment available. It is like .187 to .25 max

Jim I havnt seen the strut close up but it seems you could dremel the strut to adjust farther if need be

[bustitup]

That looks to be a pretty nice little setup. And im sure with this boat being so small you really save alot on electronics as well. What do you plan to use for a motor mount and whats your power plant gonna be? So far Im thinking of following your footsteps.

ride
I ordered this mount and plan on running a 380l with a hextronix 120 or one of those 60amp seaking esc's on 3s


http://www.offshoreelectrics.com/pro...rod=tfl-502b12

[JimClark]

I think there ia a little more you could open up the hole but it seemed ok as long as you could mount the bracket near the bottom which is easy in most boats. It would also be easy to make a different bracket to lower it even further if needed.

Jim

Jim I havnt seen the strut close up but it seems you could dremel the strut to adjust farther if need be

[Meniscus]

ride
I ordered this mount and plan on running a 380l with a hextronix 120 or one of those 60amp seaking esc's on 3s


http://www.offshoreelectrics.com/pro...rod=tfl-502b12

I'd go with the water-cooled mount

http://www.offshoreelectrics.com/proddetail.php?prod=tfl-509b13

[bustitup]

I'd go with the water-cooled mount

http://www.offshoreelectrics.com/products.php?cat=43

yup I would have done that but there out of stock

[Meniscus]

yup I would have done that but there out of stock

Oops, use the link again, I fixed it. In the 380 only size, there's one in stock. Sorry for the confusion.

[Meniscus]

OK, somehow the link doesn't work. Go to motor mounts, then one down from the 380/540 size, you'll find the 380 only size. There's also the ETTI version at the bottom of the page for 380 size.