Props for sale

[TRUCKPULL]

PROPS FOR SALE

The pic's below are from the thread I started last spring.


I have 20 props for sale.
Example of listing: X648 (46.6mm) B/S DT BC
If there is a number in the () the prop is cut down to this Diameter
B/S = Balanced and Sharpened
DT = Tetounged
BC = Back Cut
Tip = a little extra Cup on the trailing edge
Shipping is $6.00 per order unless you buy them all, then I will pay the shipping.



2- X637 Raw -------------------$12.00
5- X637 B/S DT----------------$20.00
6- X637 B/S DT ---------------$20.00
20- 1740 Raw---------------------$9.00
21- 1740 Raw---------------------$9.00
40- K51 Carbon prop ----------------$5.00


Post here the props you would like.
PM me your prop #'s
I will then send you my PayPal info

Larry
Attached Thumbnails
Current NAMBA- P Mono -1 Mile Race Record holder
Current NAMBA- P Sport -1 Mile Race Record holder
Bump & Grind Racing Props -We Like Em Smooth & Wet

[Ub Hauled]

Hi Larry,
I'll take the following...

22- V940/3 B/S ---------------$20.00
30- V947/3 Raw------------------$12.00

[gyrotron]

Hello Truck,

Of this lot of props, which one would you recommend for a PB Blackjack 29 running a 1800 Kv motor on 6s? I have heard than above 1600 kv a smaller prop should be used on a 6S count. I am currently using an x440 /3 and was looking for another prop.

Thx

[TRUCKPULL]

Hello Truck,

Of this lot of props, which one would you recommend for a PB Blackjack 29 running a 1800 Kv motor on 6s? I have heard than above 1600 kv a smaller prop should be used on a 6S count. I am currently using an x440 /3 and was looking for another prop.

Thx

The
1800kv on 6s is about 37,800 RPM
Are you running SAW's??

Every hull has a prop diamiter that it likes best. From their you ajust pitch and cup.
On a cat I would say to use about 30,000 to 32,000 RPM
On 6s this would be about 1450 to 1600 KV at 21 volts under load.

For the above reasons I can not say for sure what prop would be best for you.

Larry

[SpeedFreak_86]

Would any of those three blade props work well on a spartan with a 1600kv 4082 on 6s?

[TRUCKPULL]

Would any of those three blade props work well on a spartan with a 1600kv 4082 on 6s?

I am sorry. I don't know the Spartan Hull.

Larry

[SpeedFreak_86]

It's a 40 in v hull with a 3/16 prop shaft, rite now I'm running a 42mm x52mm

[TRUCKPULL]

A 1600kv 4082 on 6s In a 40" V hull should have a larger prop then a 42mm Diamiter.
My P Mono 33" on 4S2P runs a 48mm Dia. 3 blade Prop.

Ask this question on the question and answer fourm;
What prop for a 40" V hull running a 1600kv 4082 on 6s??
also add if it is 2P or 1P.

Larry

[gyrotron]

Truckpull.

I'll take the x438 prop #12

Thank you

[don ferrette]

32- X648 (47.4) B/S DT----------$20.00
33- X648 (47.6) B/S DT----------$20.00

If these are still available I will take both. Please p/m me with details.

[TRUCKPULL]

Truckpull.

I'll take the x438 prop #12

Thank you

PM sent

Larry

[TRUCKPULL]

32- X648 (47.4) B/S DT----------$20.00
33- X648 (47.6) B/S DT----------$20.00

If these are still available I will take both. Please p/m me with details.

PM sent

Larry

[gyrotron]

PM sent

Larry

TRUCKPULL,

Payment has been sent.

[Meniscus]

Larry, you have a 2137/3 pictured, but not listed for sale. Three questions:
1. Is it for sale?
2. What's the history on this prop, meaning did you sharpen and balance?
3. Have you modified this prop in any way or is it the original profile?

[TRUCKPULL]

Larry, you have a 2137/3 pictured, but not listed for sale. Three questions:
1. Is it for sale?
2. What's the history on this prop, meaning did you sharpen and balance?
3. Have you modified this prop in any way or is it the original profile?

Props that are pictured but not listed are already sold.

Larry